Victorian Energy Efficiency Target Regulations 2008

Regulation 6(1)(b) S.R. Nos 146/2011 Prescribed activity under regulation 6(1)(b): Installing on an electric reg. 15, 6/2012 resistance water heater a product that complies with the criteria specified in reg. 10. Part A of Schedule 2. Sch. 2 Pt A Part A—Criteria amended by S.R. No. Item 24/2013 regs 12(1), * * * * * 18(1). 2B A solar retrofit kit (solar collector, pump and controller) that— (a) is certified by an accredited body to AS/NZS 2712:2007 reissued in November 2011; and (b) achieves a minimum of 50% annual energy savings as determined in accordance with AS/NZS 4234:2008 reissued in November 2011 when modelled in zone 4 (Melbourne) using the Plumbing Characteristics specified in the Sustainability Victoria Guidelines to calculate annual solar energy savings for domestic solar water heaters produced by adding a Retrofit Kit (collectors and pump) to an existing tank (version 6.0 updated June 2011); and (c) is listed in the ESC register. Sch. 2 Pt B Part B—Calculation of carbon dioxide amended by S.R. Nos equivalents of greenhouse gases 32/2012 reg. 12, The carbon dioxide equivalent (in tonnes) of greenhouse gases 24/2013 regs 12(2)(3), to be reduced by the installation of a product referred to in an 18(2). item in Part A is calculated by multiplying the abatement factor for that item by the regional factor applying to the place where the product is installed. Authorised by the Chief Parliamentary Counsel 39 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 2—Solar retrofit kit The following are the abatement factors and regional factors for an item in Part A: Item * * * * * 2B Abatement factor: (a) If the product is installed in metropolitan Victoria: 28∙44 − [0∙001706 × (Bs + Be)]; (b) If the product is installed in regional Victoria: 30∙06 − [0∙001804 × (Bs + Be)]. * * * * * 2B Regional factor: 1. Sch. 2 Pt C (Heading) Part C—Time at which activity substituted by S.R. No. undertaken and reduction in greenhouse 96/2013 reg. 8. gas emissions occurs Sch. 2 Pt C amended by Item S.R. No. 24/2013 * * * * * regs 12(4), 18(3). 2B At the beginning of the day on which the electric resistance heater, as modified by the installed product, is first able to produce and deliver water heated by solar energy. Authorised by the Chief Parliamentary Counsel 40 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 3—Solar water heater Schedule 3—Solar water heater Sch. 3 amended by

Regulation 6(1)(c) S.R. Nos 146/2011 Prescribed activity under regulation 6(1)(c): Decommissioning a gas or reg. 16, 6/2012 liquefied petroleum gas water heater and installing a product that complies reg. 11. with the criteria specified in Part A of Schedule 3. Sch. 3 Pt A Part A—Criteria amended by S.R. No. Item 24/2013 regs 13(1), * * * * * 19(1). 3B A gas or liquefied petroleum gas boosted solar water heater that— (a) is certified by an accredited body to AS/NZS 2712:2007 reissued in November 2011; and (b) achieves a minimum of 60% annual energy savings as determined in accordance with AS/NZS 4234:2008 reissued in November 2011 when modelled in zone 4 (Melbourne); and (c) is listed in the ESC register. Sch. 3 Pt B Part B—Calculation of carbon dioxide amended by S.R. Nos equivalents of greenhouse gases 32/2012 reg. 13, The carbon dioxide equivalent (in tonnes) of greenhouse gases 24/2013 regs 13(2)(3), to be reduced by the decommissioning of a gas or liquefied 19(2). petroleum gas heater and the installation of a product referred to in an item in Part A is calculated by multiplying the abatement factor for that item by the regional factor applying to the place where the product is installed. The following are the abatement factors and regional factors for each item in Part A: Item * * * * * Authorised by the Chief Parliamentary Counsel 41 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 3—Solar water heater 3B Abatement factor: (a) If the product is a small system as determined in accordance with AS/NZS 4234:2008 reissued in November 2011 based on the system's peak daily thermal energy load delivery characteristics and— (i) is installed in metropolitan Victoria: 12⋅27 – [0⋅015 × (0⋅0573 × Bs + 0⋅2625 × Be)]; (ii) is installed in regional Victoria: 12⋅27 – [0⋅015 × (0⋅0573 × Bs + 0⋅2775 × Be)]; (b) If the product is a large system as determined in accordance with AS/NZS 4234:2008 reissued in November 2011 based on the system's peak daily thermal energy load delivery characteristics and— (i) is installed in metropolitan Victoria: 17⋅95 – [0⋅015 × (0⋅0573 × Bs + 0⋅2625 × Be)]; (ii) is installed in regional Victoria: 17⋅95 – [0⋅015 × (0⋅0573 × Bs + 0⋅2775 × Be)]; * * * * * 3B Regional factor: 1. Sch. 3 Pt C (Heading) Part C—Time at which activity substituted by S.R. No. undertaken and reduction in greenhouse 96/2013 reg. 8. gas emissions occurs Sch. 3 Pt C amended by Item S.R. No. 24/2013 * * * * * regs 13(4), 19(3). 3B At the beginning of the day which is the later of the day on which the installed product is first able to produce and deliver water heated by solar energy and the day on which the gas or liquefied petroleum gas water heater is decommissioned. Authorised by the Chief Parliamentary Counsel 42 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 4—Solar pre-heater Schedule 4—Solar pre-heater Sch. 4 (Heading)

Regulation 6(1)(d) substituted by S.R. No. Prescribed activity under regulation 6(1)(d): Installing on a gas or liquefied 146/2011 petroleum gas water heater a solar pre-heater that complies with the criteria reg. 17(b). specified in Part A of Schedule 4. Sch. 4 amended by S.R. Nos 146/2011 reg. 17(a)(c), 6/2012 reg. 12. Sch. 4 Pt A Part A—Criteria amended by S.R. No. Item 24/2013 regs 14(1), * * * * * 20(1). 4B A solar pre-heater that— (a) is certified by an accredited body to AS/NZS 2712:2007 reissued in November 2011; and (b) achieves a minimum of 50% annual energy savings as determined in accordance with AS/NZS 4234:2008 reissued in November 2011 when modelled in zone 4 (Melbourne) using the Post Heater Characteristics specified in Sustainability Victoria's Guidelines to calculate annual solar energy savings for domestic solar water heaters produced by adding a solar pre-heater to an existing gas hot water system (Version 3.0 updated June 2011); and (c) is listed in the ESC register. Authorised by the Chief Parliamentary Counsel 43 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 4—Solar pre-heater Sch. 4 Pt B amended by Part B—Calculation of carbon dioxide S.R. Nos 32/2012 equivalents of greenhouse gases reg. 14, The carbon dioxide equivalent (in tonnes) of greenhouse gases 24/2013 regs 14(2)(3), to be reduced by the installation of a product referred to in an 20(2). item in Part A is calculated by multiplying the abatement factor for that item by the regional factor applying to the place where the product is installed. The following are the abatement factors and regional factors for an item in Part A: Item * * * * * 4B Abatement factor: (a) If the product is a small system as determined in accordance AS/NZS 4234:2008 reissued in November 2011 based on the system's peak daily thermal energy load delivery characteristics and— (i) is installed in metropolitan Victoria: 7⋅53 – [0⋅006 × (0⋅0573 × Bs + 0⋅2625 × Be)]; (ii) is installed in regional Victoria: 7⋅53 – [0⋅006 × (0⋅0573 × Bs + 0⋅2775 × Be)]; (b) If the product is a large system as determined in accordance with AS/NZS 4234:2008 reissued in November 2011 based on the system's peak daily thermal energy load delivery characteristics and— (i) is installed in metropolitan Victoria: 10⋅26 – [0⋅006 × (0⋅0573 × Bs + 0⋅2625 × Be)]; (ii) is installed in regional Victoria: 10⋅26 – [0⋅006 × (0⋅0573 × Bs + 0⋅2775 × Be)]; * * * * * 4B Regional factor: 1. Authorised by the Chief Parliamentary Counsel 44 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 4—Solar pre-heater Part C—Time at which activity Sch. 4 Pt C (Heading) undertaken and reduction in greenhouse substituted by S.R. No. gas emissions occurs 96/2013 reg. 8. Item Sch. 4 Pt C amended by * * * * * S.R. No. 24/2013 4B At the beginning of the day on which the gas or liquefied regs 14(4), 20(3). petroleum gas water heater, as modified by the installed product, is first able to produce and deliver water heated by solar energy. Authorised by the Chief Parliamentary Counsel 45 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 5—High efficiency ducted gas heater replacing a ducted gas heater Sch. 5 amended by Schedule 5—High efficiency ducted gas S.R. Nos 146/2011 heater replacing a ducted gas heater reg. 18, 6/2012 Regulation 6(1)(e) reg. 13. Prescribed activity under regulation 6(1)(e): Decommissioning a ducted gas space heater and installing a product that complies with the criteria specified in Part A of Schedule 5. Part A—Criteria Item 5A Ducted gas heater certified by an accredited body to achieve a minimum 5 star rating when tested and rated in accordance with AS 4556—2000 or AS 4556—2011 with a minimum rated output heating capacity of 10 kW as determined in accordance with AS 4556—2000 or AS 4556—2011 and listed in the ESC register. Sch. 5 Pt B amended by Part B—Calculation of carbon dioxide S.R. No. 32/2012 equivalents of greenhouse gases reg. 15. The carbon dioxide equivalent (in tonnes) of greenhouse gases to be reduced by the decommissioning of a ducted gas space heater and the installation of a product referred to in an item in Part A is calculated by multiplying the abatement factor for that item by the regional factor applying to the place where the product is installed. The following are the abatement factors and regional factors for an item in Part A: Item 5A Abatement factor: (a) If the product has a rated output heating capacity of not less than 10 and not more than 18 kW as determined in accordance with AS 4556—2000 or AS 4556—2011 and has a star rating determined in accordance with AS 4556—2000 or AS 4556—2011 of— Authorised by the Chief Parliamentary Counsel 46 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 5—High efficiency ducted gas heater replacing a ducted gas heater (i) not less than 5⋅0 and not more than 5⋅49: 7⋅74; (ii) 5⋅5 or more: 9⋅67; (b) If the product has a rated output heating capacity of more than 18kW and not more than 28 kW as determined in accordance with AS 4556—2000 or AS 4556—2011 and has a star rating determined in accordance with AS 4556—2000 or AS 4556—2011 of— (i) not less than 5⋅0 and not more than 5⋅49: 9⋅76; (ii) 5⋅5 or more: 12⋅20; (c) If the product has a rated output heating capacity of more than 28 kW as determined in accordance with AS 4556—2000 or AS 4556—2011 and has a star rating determined in accordance with AS 4556— 2000 or AS 4556—2011 of— (i) not less than 5⋅0 and not more than 5⋅49: 12⋅16; (ii) 5⋅5 or more: 15⋅20. 5A Regional factor: (a) If the product is installed in metropolitan Victoria: 1; (b) If the product is installed in regional Victoria—climatic region Mild: 1; (c) If the product is installed in regional Victoria—climatic region Cold: 1⋅61; (d) If the product is installed in regional Victoria—climatic region Hot: 0⋅71. Authorised by the Chief Parliamentary Counsel 47 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 5—High efficiency ducted gas heater replacing a ducted gas heater Sch. 5 Pt C (Heading) Part C—Time at which activity substituted by S.R. No. undertaken and reduction in greenhouse 96/2013 reg. 8. gas emissions occurs Item 5A At the beginning of the day which is the later of the day on which the installed product is first able to produce and deliver ducted gas heating and the day on which the ducted gas space heater is decommissioned. Authorised by the Chief Parliamentary Counsel 48 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 6—High efficiency ducted gas heater replacing a central electric resistance heater Schedule 6—High efficiency ducted Sch. 6 amended by gas heater replacing a central electric S.R. No. 6/2012 reg. 14. resistance heater

Regulation 6(1)(f) Prescribed activity under regulation 6(1)(f): Decommissioning a central electric resistance heater that provides heating to a space with a floor area of at least 100m2 and installing a product that complies with the criteria specified in Part A of Schedule 6. Part A—Criteria Item 6A Ducted gas heater certified by an accredited body to achieve a minimum 5 star rating when tested and rated in accordance with AS 4556—2000 with a minimum rated output heating capacity of 10 kW as determined in accordance with AS 4556—2000 and listed in the ESC register. Sch. 6 Pt B Part B—Calculation of carbon dioxide amended by S.R. No. equivalents of greenhouse gases 32/2012 reg. 16. The carbon dioxide equivalent (in tonnes) of greenhouse gases to be reduced by the decommissioning of a central electric resistance heater and the installation of a product referred to in an item in Part A is calculated by multiplying the abatement factor for that item by the regional factor applying to the place where the product is installed. The following are the abatement factors and regional factors for each item in Part A: Item 6A Abatement factor: (a) If the product has a rated output heating capacity of not less than 10 and not more than 18 kW as determined in accordance with AS 4556—2000 and Authorised by the Chief Parliamentary Counsel 49 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 6—High efficiency ducted gas heater replacing a central electric resistance heater has a star rating determined in accordance with AS 4556—2000 of— (i) not less than 5⋅0 and not more than 5⋅49: 119⋅43; (ii) 5⋅5 or more: 121⋅44; (b) If the product has a rated output heating capacity of more than 18 and not more than 28 kW as determined in accordance with AS 4556—2000 and has a star rating determined in accordance with AS 4556—2000 of— (i) not less than 5⋅0 and not more than 5⋅49: 151⋅07; (ii) 5⋅5 or more: 153⋅61; (c) If the product has a rated output heating capacity of more than 28 kW as determined in accordance with AS 4556—2000 and has a star rating determined in accordance with AS 4556—2000 of— (i) not less than 5⋅0 and not more than 5⋅49: 188⋅48; (ii) 5⋅5 or more: 191⋅66. 6A Regional factor: (a) If the product is installed in metropolitan Victoria: 1; (b) If the product is installed in regional Victoria—climatic region Mild: 1⋅08; (c) If the product is installed in regional Victoria—climatic region Cold: 1⋅74; (d) If the product is installed in regional Victoria—climatic region Hot: 0⋅76. Authorised by the Chief Parliamentary Counsel 50 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 6—High efficiency ducted gas heater replacing a central electric resistance heater Part C—Time at which activity Sch. 6 Pt C (Heading) undertaken and reduction in greenhouse substituted by S.R. No. gas emissions occurs 96/2013 reg. 8. Item 6A At the beginning of the day which is the later of the day on which the installed product is first able to produce and deliver ducted gas heating and the day on which the central electric resistance heater is decommissioned. Authorised by the Chief Parliamentary Counsel 51 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 7—High efficiency ducted air to air heat pump replacing a ducted air to air heat pump Sch. 7 amended by Schedule 7—High efficiency ducted air to S.R. Nos 6/2012 reg. 15, air heat pump replacing a ducted air to 167/2015 reg. 9(1). air heat pump

Regulation 6(1)(g) Prescribed activity under regulation 6(1)(g): Decommissioning a ducted air to air heat pump and installing a product that complies with the criteria specified in Part A of Schedule 7. Part A—Criteria Item Sch. 7 Pt A 7A A product that— item 7A substituted by S.R. No. (a) complies with the MEPS requirement set out in 167/2015 column 4 of Table 3.1 of AS/NZS 3823.2:2013; and reg. 9(2). (b) achieves an annual coefficient of performance, as determined in accordance with AS/NZS 3823.2:2013, of not less than 3.7; and (c) has a rated output heating capacity, as determined in accordance with AS/NZS 3823.1.2:2012, of not less than 10kW at the H1 temperature condition; and (d) is listed on the ESC register. Sch. 7 Pt B amended by Part B—Calculation of carbon dioxide S.R. No. 32/2012 equivalents of greenhouse gases reg. 17. The carbon dioxide equivalent (in tonnes) of greenhouse gases to be reduced by the decommissioning of a ducted air to air heat pump and the installation of a product referred to in an item in Part A is calculated by multiplying the abatement factor for that item by the regional factor applying to the place where the product is installed. Authorised by the Chief Parliamentary Counsel 52 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 7—High efficiency ducted air to air heat pump replacing a ducted air to air heat pump The following are the abatement factors and regional factors for each item in Part A: Item 7A Abatement factor: Sch. 7 Pt B item 7A Abatement (a) If the product has a heating capacity, as determined factor: in accordance with AS/NZS 3823.1.2:2012, of not substituted by S.R. No. less than 10 and not more than 18 kW at the 167/2015 H1 temperature condition and has an annual reg. 9(3). coefficient of performance, as determined in accordance with AS/NZS 3823.2:2013, of— (i) not less than 3⋅7 and not more than 3∙99: 1∙25; (ii) not less than 4 and not more than 4∙29: 4∙62; (iii) not less than 4∙3 and not more than 4∙59: 7∙52; (iv) 4∙6 or more: 10∙04; (b) If the product has a heating capacity, as determined in accordance with AS/NZS 3823.1.2:2012, of more than 18 and not more than 28 kW at the H1 temperature condition and has an annual coefficient of performance, as determined in accordance with AS/NZS 3823.2:2013, of— (i) not less than 3∙7 and not more than 3∙99: 3∙25; (ii) not less than 4 and not more than 4∙29: 7∙51; (iii) not less than 4⋅3 and not more than 4∙59: 11∙18; (iv) 4∙6 or more: 14∙37; Authorised by the Chief Parliamentary Counsel 53 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 7—High efficiency ducted air to air heat pump replacing a ducted air to air heat pump (c) If the product has a heating capacity, as determined in accordance with AS/NZS 3823.1.2:2012, of more than 28 kW at the H1 temperature condition and has an annual coefficient of performance, as determined in accordance with AS/NZS 3823.2:2013, of— (i) not less than 3∙7 and not more than 3∙99: 6∙26; (ii) not less than 4 and not more than 4∙29: 11∙58; (iii) not less than 4∙3 and not more than 4∙59: 16∙15; (iv) 4∙6 or more: 20∙13. Sch. 7 Pt B 7A Regional factor: item 7A Regional factor: (a) If the product is installed in metropolitan amended by Victoria: 1; S.R. No. 167/2015 (b) If the product is installed in regional reg. 9(4). Victoria—climatic region Mild: 1⋅06; (c) If the product is installed in regional Victoria—climatic region Cold: 1∙72; (d) If the product is installed in regional Victoria—climatic region Hot: 0∙75. Sch. 7 Pt C (Heading) Part C—Time at which activity substituted by S.R. No. undertaken and reduction in greenhouse 96/2013 reg. 8. gas emissions occurs Item 7A At the beginning of the day which is the later of the day on which the installed product is first able to produce and deliver heating and the day on which the ducted air to air heat pump is decommissioned. Authorised by the Chief Parliamentary Counsel 54 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 8—High efficiency ducted air to air heat pump replacing central electric resistance heater Schedule 8—High efficiency ducted air to Sch. 8 amended by air heat pump replacing central electric S.R. Nos 6/2012 reg. 16, resistance heater 167/2015 reg. 10(1).

Regulation 6(1)(h) Prescribed activity under regulation 6(1)(h): Decommissioning a central electric resistance heater that provides heating to a space with a floor area of at least 100m2 and installing a product that complies with the criteria specified in Part A of Schedule 8. Part A—Criteria Item 8A A product that— Sch. 8 Pt A item 8A substituted by (a) complies with the MEPS requirement set out in S.R. No. column 4 of Table 3.1 of AS/NZS 3823.2:2013; and 167/2015 reg. 10(2). (b) achieves an annual coefficient of performance, as determined in accordance with AS/NZS 3823.2:2013, of not less than 3.7; and (c) has a rated output heating capacity, as determined in accordance with AS/NZS 3823.1.2:2012, of not less than 10 kW at the H1 temperature condition; and (d) is listed in the ESC register. Sch. 8 Pt B Part B—Calculation of carbon dioxide amended by S.R. No. equivalents of greenhouse gases 32/2012 reg. 18. The carbon dioxide equivalent (in tonnes) of greenhouse gases to be reduced by the decommissioning of a central electric resistance heater and the installation of a product referred to in an item in Part A is calculated by multiplying the abatement factor for that item by the regional factor applying to the place where the product is installed. Authorised by the Chief Parliamentary Counsel 55 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 8—High efficiency ducted air to air heat pump replacing central electric resistance heater The following are the abatement factors and regional factors for each item in Part A: Item Sch. 8 Pt B 8A Abatement factor: item 8A Abatement factor: (a) If the product has a heating capacity, as determined substituted by in accordance with AS/NZS 3823.1.2:2012, of not S.R. No. 167/2015 less than 10 and not more than 18 kW at the reg. 10(3). H1 temperature condition and has an annual coefficient of performance, as determined in accordance with AS/NZS 3823.2:2013, of— (i) not less than 3∙7 and not more than 3∙99: 102∙0; (ii) not less than 4 and not more than 4∙29: 107∙0; (iii) not less than 4∙3 and not more than 4∙59: 111∙2; (iv) 4∙6 or more: 114∙8; (b) If the product has a heating capacity, as determined in accordance with AS/NZS 3823.1.2:2012, of more than 18 and not more than 28 kW at the H1 temperature condition and has an annual coefficient of performance, as determined in accordance with AS/NZS 3823.2:2013, of— (i) not less than 3∙7 and not more than 3∙99: 129·9; (ii) not less than 4 and not more than 4∙29: 136∙0; (iii) not less than 4∙3 and not more than 4∙59: 141∙2; (iv) 4∙6 or more: 145∙8; Authorised by the Chief Parliamentary Counsel 56 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 8—High efficiency ducted air to air heat pump replacing central electric resistance heater (c) If the product has a heating capacity, as determined in accordance with AS/NZS 3823.1.2:2012, of more than 28 kW at the H1 temperature condition and has an annual coefficient of performance, as determined in accordance with AS/NZS 3823.2:2013, of— (i) not less than 3∙7 and not more than 3∙99: 165∙4; (ii) not less than 4 and not more than 4∙29: 172∙7; (iii) not less than 4∙3 and not more than 4∙59: 179∙0; (iv) 4∙6 or more: 184∙5. 8A Regional factor: Sch. 8 Pt B item 8A Regional (a) If the product is installed in metropolitan factor: Victoria: 1⋅00; amended by S.R. No. (b) If the product is installed in regional 167/2015 reg. 10(4). Victoria—climatic region Mild: 1⋅06; (c) If the product is installed in regional Victoria—climatic region Cold: 1∙79; (d) If the product is installed in regional Victoria—climatic region Hot: 0∙61. Sch. 8 Pt C Part C—Time at which activity (Heading) substituted by undertaken and reduction in greenhouse S.R. No. 96/2013 reg. 8. gas emissions occurs Item 8A At the beginning of the day which is the later of the day on which the installed product is first able to produce and deliver heating and the day on which the central electric resistance heater is decommissioned. Authorised by the Chief Parliamentary Counsel 57 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 9—Gas or liquefied petroleum gas space heater Sch. 9 amended by Schedule 9—Gas or liquefied petroleum S.R. No. 6/2012 reg. 17. gas space heater

Regulation 6(1)(i) Prescribed activity under regulation 6(1)(i): Installing a gas or liquefied petroleum gas space heater that is flued and complies with the criteria specified in Part A of Schedule 9. Part A—Criteria Item 9A A product certified by an accredited body, achieving a minimum energy star rating of 4 when tested and rated to AS 4553—2000 or AS 4553—2008, with a minimum rated output heating capacity of 2 kW as determined in accordance with AS 4553—2000 or AS 4553—2008 and listed in the ESC register. Sch. 9 Pt B amended by Part B—Calculation of carbon dioxide S.R. No. 32/2012 equivalents of greenhouse gases reg. 19. The carbon dioxide equivalent (in tonnes) of greenhouse gases to be reduced by the installation of a product referred to in an item in Part A is calculated by multiplying the abatement factor for that item by the regional factor applying to the place where the product is installed. The following are the abatement factors and regional factors for each item in Part A: Sch. 9 Pt B 9A Abatement factor: item 9A Abatement factor: (a) If the product provides a rated output heating amended by capacity of not less than 2 and not more than 3 kW S.R. No. 167/2015 as determined in accordance with AS 4553—2000 reg. 11(a). and has an energy star rating determined in accordance with AS 4553—2000 of— (i) not less than 4⋅0 and not more than 4⋅9: 5∙36; (ii) 5 or more: 5∙86; Authorised by the Chief Parliamentary Counsel 58 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 9—Gas or liquefied petroleum gas space heater (b) If the product provides a rated output heating capacity of more than 3 and not more than 6 kW as determined in accordance with AS 4553—2000 and has an energy star rating determined in accordance with AS 4553—2000 of— (i) not less than 4.0 and not more than 4⋅9: 9∙61; (ii) 5 or more: 10∙55; (c) If the product provides a rated output heating capacity of more than 6 kW as determined in accordance with AS 4553—2000 and has an energy star rating when determined in accordance with AS 4553—2000 of— (i) not less than 4⋅0 and not more than 4⋅9: 13∙22; (ii) 5 or more: 14∙39. 9A Regional factor: Sch. 9 Pt B item 9A Regional (a) If the product has an energy star rating determined in factor: accordance with AS 4553—2000 of not less than 4⋅0 amended by S.R. No. and not more than 4⋅9 and— 167/2015 reg. 11(b). (i) is installed in metropolitan Victoria: 1⋅00; (ii) is installed in regional Victoria— climatic region Mild: 0∙22; (iii) is installed in regional Victoria— climatic region Cold: 0∙36; (iv) is installed in regional Victoria— climatic region Hot: 0∙15; Authorised by the Chief Parliamentary Counsel 59 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 9—Gas or liquefied petroleum gas space heater (b) If the product has an energy star rating determined in accordance with AS 4553—2000 of 5⋅0 or more and— (i) is installed in metropolitan Victoria: 1⋅00; (ii) is installed in regional Victoria— climatic region Mild: 0∙29; (iii) is installed in regional Victoria— climatic region Cold: 0∙46; (iv) is installed in regional Victoria— climatic region Hot: 0∙20. Sch. 9 Pt C (Heading) Part C—Time at which activity substituted by S.R. No. undertaken and reduction in greenhouse 96/2013 reg. 8. gas emissions occurs Item 9A At the beginning of the day on which the installed product is first able to produce and deliver heating. Authorised by the Chief Parliamentary Counsel 60 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 10—Space air to air heat pump Schedule 10—Space air to air heat pump Sch. 10 amended by

Regulation 6(1)(j) S.R. Nos 146/2011 Prescribed activity under regulation 6(1)(j): Installing a space air to air heat reg. 19, 6/2012 pump that complies with the criteria specified in Part A of Schedule 10. reg. 18, 167/2015 reg. 12(1). Part A—Criteria Item 10A A product that— Sch. 10 Pt A item 10A substituted by (a) complies with the MEPS requirement set out in S.R. No. column 4 of Table 3.1 of AS/NZS 3823.2:2013; and 167/2015 reg. 12(2). (b) achieves an annual coefficient of performance, as determined in accordance with AS/NZS 3823.2:2013 when tested in accordance with AS/NZS 3823.1.1:2012, of not less than 4; and (c) has a heating capacity, as determined in accordance with AS/NZS 3823.1.1:2012, of not less than 2 kW at the H1 temperature condition; and (d) is listed in the ESC register. Sch. 10 Pt B Part B—Calculation of carbon dioxide amended by S.R. No. equivalents of greenhouse gases 32/2012 reg. 20. The carbon dioxide equivalent (in tonnes) of greenhouse gases to be reduced by the installation of a product referred to in an item in Part A is calculated by multiplying the abatement factor for that item by the regional factor applying to the place where the product is installed. The following are the abatement factors and regional factors for each item in Part A: Authorised by the Chief Parliamentary Counsel 61 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 10—Space air to air heat pump Item Sch. 10 Pt B 10A Abatement factor: item 10A Abatement factor: (a) If the product has a heating capacity, as determined substituted by in accordance with AS/NZS 3823.1.1:2012, of not S.R. No. 167/2015 less than 2 and not more than 2∙99 kW at the reg. 12(3). H1 temperature condition and has an annual coefficient of performance, as determined in accordance with AS/NZS 3823.2:2013, of— (i) not less than 4 and not more than 4∙49: 4∙64; (ii) not less than 4∙5 and not more than 4∙99: 5∙48; (iii) not less than 5 and not more than 5∙49: 6∙14; (iv) 5∙5 or more: 6∙69; (b) If the product has a heating capacity, as determined in accordance with AS/NZS 3823.1.1:2012, of not less than 3 and not more than 6 kW at the H1 temperature condition and has an annual coefficient of performance, as determined in accordance with AS/NZS 3823.2:2013, of— (i) not less than 4 and not more than 4∙49: 8∙33; (ii) not less than 4∙5 and not more than 4∙99: 9∙91; (iii) not less than 5 and not more than 5∙49: 11∙17; (iv) 5∙5 or more: 12∙20; (c) If the product has a heating capacity, as determined in accordance with AS/NZS 3823.1.1:2012, of more than 6 kW at the H1 temperature condition and has an annual coefficient of performance, as determined in accordance with AS/NZS 3823.2:2013, of— Authorised by the Chief Parliamentary Counsel 62 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 10—Space air to air heat pump (i) not less than 4 and not more than 4∙49: 11∙51; (ii) not less than 4∙5 and not more than 4∙99: 13∙42; (iii) not less than 5 and not more than 5∙49: 14∙95; (iv) 5∙5 or more: 16∙20. 10A Regional factor: Sch. 10 Pt B item 10A Regional (a) If the product has an annual coefficient of factor: performance, as determined in accordance substituted by S.R. No. with AS/NZS 3823.2:2013, of not less 167/2015 than 4 and is installed in metropolitan reg. 12(4). Victoria: 1⋅00; (b) If the product has an annual coefficient of performance, as determined in accordance with AS/NZS 3823.2:2013, of not less than 4 and not more than 4∙49 and— (i) is installed in regional Victoria— climatic region Mild: 0∙12; (ii) is installed in regional Victoria— climatic region Cold: 0∙24; (iii) is installed in regional Victoria— climatic region Hot: 0∙02; (c) If the product has an annual coefficient of performance, as determined in accordance with AS/NZS 3823.2:2013, of not less than 4∙5 and not more than 4∙99 and— (i) is installed in regional Victoria— climatic region Mild: 0∙27; (ii) is installed in regional Victoria— climatic region Cold: 0∙44; (iii) is installed in regional Victoria— climatic region Hot: 0∙16; Authorised by the Chief Parliamentary Counsel 63 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 10—Space air to air heat pump (d) If the product has an annual coefficient of performance, as determined in accordance with AS/NZS 3823.2:2013, of not less than 5 and not more than 5∙49 and— (i) is installed in regional Victoria— climatic region Mild: 0∙39; (ii) is installed in regional Victoria— climatic region Cold: 0∙63; (iii) is installed in regional Victoria—climatic region Hot: 0∙29; (e) If the product has an annual coefficient of performance, as determined in accordance with AS/NZS 3823.2:2013, of 5∙5 or more and— (i) is installed in regional Victoria— climatic region Mild: 0∙50; (ii) is installed in regional Victoria— climatic region Cold: 0∙79; (iii) is installed in regional Victoria— climatic region Hot: 0∙38. Sch. 10 Pt C (Heading) Part C—Time at which activity substituted by S.R. No. undertaken and reduction in greenhouse 96/2013 reg. 8. gas emissions occurs Item 10A At the beginning of the day on which the installed product is first able to produce and deliver heating. Authorised by the Chief Parliamentary Counsel 64 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 11—Ceiling insulation Schedule 11—Ceiling insulation Sch. 11 amended by

Regulation 6(2)(a) S.R. Nos 6/2012 reg. 19, Prescribed activity under regulation 6(2)(a): Installing a product in 32/2012 accordance with AS3999—2015 published on 23 July 2015 in a ceiling area reg. 21(a), 16/2016 not previously insulated for a minimum area of 20m2, being a product that reg. 6(1). complies with the criteria specified in Part A of Schedule 11. Part A—Criteria Item 11A A product or combination of products— Sch. 11 Pt A item 11A substituted by (a) that achieves a material R-value of not less than 3·5 S.R. No. when measured in accordance with section 2.3 of 16/2016 reg. 6(2). AS/NZS 4859.1:2002 incorporating Amendment No. 1 published on 28 December 2006; and (b) each of which— (i) is not conductive; and (ii) complies with the performance criteria of AS/NZS 4859.1:2002 incorporating Amendment No. 1 published on 28 December 2006. Sch. 11 Pt B Part B—Calculation of carbon dioxide amended by S.R. No. equivalents of greenhouse gases 32/2012 reg. 21(b). The carbon dioxide equivalent (in tonnes) of greenhouse gases to be reduced by the installation of a product or products referred to in an item in Part A is calculated by multiplying the area of insulation (m2) by the abatement factor for that item by the regional factor applying to the place where the product or products are installed. Authorised by the Chief Parliamentary Counsel 65 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 11—Ceiling insulation The following are the abatement factors and regional factors for each item in Part A: Item 11A Abatement factor: 0⋅256; 11A Regional factor: (a) If the product or products are installed in metropolitan Victoria: 1⋅06; (b) If the product or products are installed in regional Victoria—climatic region Mild: 0⋅86; (c) If the product or products are installed in regional Victoria—climatic region Cold: 1⋅23; (d) If the product or products are installed in regional Victoria—climatic region Hot: 0⋅79. Sch. 11 Pt C (Heading) Part C—Time at which activity substituted by S.R. No. undertaken and reduction in greenhouse 96/2013 reg. 8. gas emissions occurs Item 11A At the beginning of the day on which the installation of the product or products is completed. Authorised by the Chief Parliamentary Counsel 66 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 12—Under floor insulation Schedule 12—Under floor insulation Sch. 12 amended by

Regulation 6(1)(k) S.R. Nos 6/2012 reg. 20, Prescribed activity under regulation 6(1)(k): Installing, in respect of a floor 32/2012 area that is not insulated, a product that complies with the criteria specified reg. 22(a). in Part A of Schedule 12 as under floor insulation for a minimum of 20m2 in accordance with AS 3999—1992 published on 16 April 1992 incorporating Amendment No. 1 published on 9 March 2012. Part A—Criteria Item 12A A product that complies, or two or more products that, when installed together, comply with the performance requirements of AS/NZS 4859.1:2002 (insulation material) and achieves a minimum winter R-value of 2⋅5 when measured and labelled in accordance with AS/NZS 4859.1:2002. Sch. 12 Pt B Part B—Calculation of carbon dioxide amended by S.R. No. equivalents of greenhouse gases 32/2012 reg. 22(b). The carbon dioxide equivalent (in tonnes) of greenhouse gases to be reduced by the installation of a product or products referred to in an item in Part A is calculated by multiplying the area of insulation (m2) by the abatement factor for that item by the regional factor applying to the place where the product or products are installed. The following are the abatement factors and regional factors for each item in Part A: Item 12A Abatement factor: 0⋅073 Regional factor: (a) If the product or products are installed in metropolitan Victoria: 1⋅06; (b) If the product or products are installed in regional Victoria—climatic region Mild: 0⋅86; Authorised by the Chief Parliamentary Counsel 67 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 12—Under floor insulation (c) If the product or products are installed in regional Victoria—climatic region Cold: 1⋅23; (d) If the product or products are installed in regional Victoria—climatic region Hot: 0⋅79. Sch. 12 Pt C (Heading) Part C—Time at which activity substituted by S.R. No. undertaken and reduction in greenhouse 96/2013 reg. 8. gas emissions occurs Item 12A At the beginning of the day on which the installation of the product or products is completed. Authorised by the Chief Parliamentary Counsel 68 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 13—Thermally efficient window Schedule 13—Thermally efficient window Sch. 13 amended by

Regulation 6(1)(l) S.R. No. 6/2012 reg. 21. Prescribed activity under regulation 6(1)(l): Installing, in place of one or more windows in an external wall, at least 5m2 of glazing or glazed product that complies with the criteria specified in Part A of Schedule 13. Part A—Criteria Item 13A A product that complies with the performance requirements of AS 2047—1999 and AS 1288—2006, has a Total U-value of not more than 4, is WERS rated and labelled to a minimum of 4 stars for heating and is listed in the ESC register. Sch. 13 Pt B Part B—Calculation of carbon dioxide amended by S.R. No. equivalents of greenhouse gases 32/2012 reg. 23. The carbon dioxide equivalent (in tonnes) of greenhouse gases to be reduced by the installation of a product referred to in an item in Part A is calculated by multiplying the area of glazing (m2) by the abatement factor for that item by the regional factor applying to the place where the product is installed. The following are the abatement factors and regional factors for each item in Part A: Item 13A Abatement factor: If the product has a WERS rating on heating of— (a) not less than 4⋅0 and not more than 4⋅9 stars: 0⋅394; (b) not less than 5⋅0 and not more than 5⋅9 stars: 0⋅493; (c) 6⋅0 or more stars: 0⋅591. Authorised by the Chief Parliamentary Counsel 69 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 13—Thermally efficient window 13A Regional factor: (a) If the product or products are installed in metropolitan Victoria: 1⋅03; (b) If the product or products are installed in regional Victoria—climatic region Mild: 0⋅92; (c) If the product or products are installed in regional Victoria—climatic region Cold: 1⋅41; (d) If the product or products are installed in regional Victoria—climatic region Hot: 0⋅74. Sch. 13 Pt C (Heading) Part C—Time at which activity substituted by S.R. No. undertaken and reduction in greenhouse 96/2013 reg. 8. gas emissions occurs Item 13A At the beginning of the day on which the installation of the product is completed. Authorised by the Chief Parliamentary Counsel 70 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 14—Installation of product on single glazed window raising thermal efficiency Schedule 14—Installation of product on Sch. 14 amended by single glazed window raising thermal S.R. No. 6/2012 reg. 22. efficiency

Regulation 6(1)(m) Prescribed activity under regulation 6(1)(m): Installing, on one or more single glazed windows in an external wall for a minimum glazing area of 5m2, a product that complies with the criteria specified in Part A of Schedule 14. Part A—Criteria Item 14A A product that, when installed on a single glazed window, results in a still air gap being created between the single glazed window and the product and raises the thermal efficiency performance of the window. Sch. 14 Pt B Part B—Calculation of carbon dioxide amended by S.R. No. equivalents of greenhouse gases 32/2012 reg. 24. The carbon dioxide equivalent (in tonnes) of greenhouse gases to be reduced by the installation of a product referred to in an item in Part A is calculated by multiplying the area of glazing (m2) by the abatement factor for that item by the regional factor applying to the place where the product is installed. The following are the abatement factors and regional factors for each item in Part A: Item 14A Abatement factor: (a) If the product is glass or acrylic: 0⋅213; (b) If the product is window film: 0⋅071. Authorised by the Chief Parliamentary Counsel 71 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008

Schedule 14—Installation of product on single glazed window raising thermal efficiency 14A Regional factor: (a) If the product is installed in metropolitan Victoria: 1⋅03; (b) If the product is installed in regional Victoria—climatic region Mild: 0⋅92; (c) If the product is installed in regional Victoria—climatic region Cold: 1⋅41; (d) If the product is installed in regional Victoria—climatic region Hot: 0⋅74. Sch. 14 Pt C (Heading) Part C—Time at which activity substituted by S.R. No. undertaken and reduction in greenhouse 96/2013 reg. 8. gas emissions occurs Item 14A At the beginning of the day on which the installation of the product is completed. Authorised by the Chief Parliamentary Counsel 72 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 15—Weather sealing Schedule 15—Weather sealing Sch. 15 amended by Regulation 6(2)(b) S.R. Nos 6/2012 reg. 23, Prescribed activity under regulation 6(2)(b): Undertaking in the premises one 32/2012 or more of the weather sealing activities referred to in regulation 6AA unless reg. 25, 96/2013 reg. 8, that activity results, or those activities together result, in the volume of air substituted by that is exchanged at the premises each hour being less than 50% of the S.R. No. volume of the premises, or the premises failing to comply with Part 3.8.5 of 52/2017 reg. 9. the Building Code as amended from time to time. Part A—Criteria Item 15A A door sealing product or weather stripping product, or a combination of such products— (a) each of which is covered by a warranty against defects for a period of at least 2 years from the date of installation; and (b) that is listed on the ESC register as a single product or as a combination of products (as the case requires). 15B A window sealing product or weather stripping product, or a combination of such products— (a) each of which is covered by a warranty against defects for a period of at least 2 years from the date of installation; and (b) that is listed on the ESC register as a single product or as a combination of products (as the case requires). 15C A product, being a ceiling or wall exhaust fan, that— (a) expels air either outside or into the roof space of the premises; and (b) is fitted with a self-closing damper, flap, filter or other sealing product that allows airflow through the exhaust of the fan when the fan is operating, Authorised by the Chief Parliamentary Counsel 73 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 15—Weather sealing but restricts airflow when the fan is not operating; and (c) is covered by a warranty against defects for a period of at least 2 years from the date of installation; and (d) is listed on the ESC register. 15D A product, being a self-closing damper, flap, filter or other sealing product that— (a) when installed on a ceiling or wall exhaust fan, allows airflow through the exhaust of the fan when the fan is operating and restricts airflow when the fan is not operating; and (b) is covered by a warranty against defects for a period of at least 2 years from the date of installation; and (c) is listed on the ESC register. 15E A product that— (a) is made of a robust non-shrinking sealing material; and (b) is covered by a warranty against defects for a period of at least 2 years from the date of installation; and (c) is listed on the ESC register. 15F A product that— (a) when fitted to a chimney or flue of an open fireplace used to burn solid fuel when closed— (i) restricts the airflow into or out of the chimney or flue; and (ii) allows the fireplace to operate safely and effectively when open; and (b) is designed to be fitted permanently to the chimney or flue; and Authorised by the Chief Parliamentary Counsel 74 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 15—Weather sealing (c) is covered by a warranty against defects for a period of at least 5 years from the date of installation; and (d) is listed on the ESC register. 15G A product that— (a) when fitted to a chimney or flue of an open fireplace used to burn solid fuel, restricts the airflow into or out of the chimney or flue; and (b) is designed to be installed on a temporary or seasonal basis; and (c) is covered by a warranty against defects for a period of at least 2 years from the date of installation; and (d) is listed on the ESC register. 15H A product that— (a) when installed to cover the ceiling outlet of a ducted evaporative cooling system, restricts airflow from inside the residential premises into the evaporative cooling ductwork; and (b) is designed to be installed on a temporary or seasonal basis; and (c) is covered by a warranty against defects for a period of at least 2 years from the date of installation; and (d) is supplied for installation with instructions regarding— (i) the installation and removal of the product; and (ii) the time of year that the product should be installed and removed; and (e) is listed on the ESC register. Authorised by the Chief Parliamentary Counsel 75 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 15—Weather sealing Part B—Calculation of carbon dioxide equivalents of greenhouse gases The carbon dioxide equivalent (in tonnes) of greenhouse gases to be reduced by undertaking one or more of the weather sealing activities referred to in regulation 6AA is the sum of the figures obtained by multiplying, for each item in Part A, the number of products or combinations of products referred to in that item that are installed as part of the activity by the abatement factor for that item (or, in the case of item 15B, by the area in m2 of the window the frame of which is sealed) and by the regional factor applying to the place where the products or combinations of products are installed. The following are the abatement factors and regional factors for each item in Part A: Item 15A Abatement factor: For each door: (a) If the product, or one or more of the products, is covered by a warranty against defects for a period of at least 2 years, but less than 5 years: 0·3025; (b) If the product, or each of the products, is covered by a warranty against defects for a period of at least 5 years: 0·605. 15B Abatement factor: For each m2 of the window, the frame of which is sealed: (a) If the product, or one or more of the products, is covered by a warranty against defects for a period of at least 2 years, but less than 5 years: 0·0135; Authorised by the Chief Parliamentary Counsel 76 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 15—Weather sealing (b) If the product, or each of the products, is covered by a warranty against defects for a period of at least 5 years: 0·027. 15C Abatement factor: For each exhaust fan: (a) If the warranty against defects covers a period of at least 2 years, but less than 5 years: 0·464; (b) If the warranty against defects covers a period of at least 5 years: 0·928. 15D Abatement factor: For each exhaust fan: (a) If the warranty against defects covers a period of at least 2 years, but less than 5 years: 0·899; (b) If the warranty against defects covers a period of at least 5 years: 1·798. 15E Abatement factor: For each ventilation opening sealed or closed: (a) If the warranty against defects covers a period of at least 2 years, but less than 5 years: 0·118; (b) If the warranty against defects covers a period of at least 5 years: 0·236. 15F Abatement factor: For each chimney or flue in which a product is installed: 5·234. 15G Abatement factor For each chimney or flue in which a product is installed: 2·617. Authorised by the Chief Parliamentary Counsel 77 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 15—Weather sealing 15H Abatement factor: For each evaporative cooling cover installed: (a) If the warranty against defects covers a period of at least 2 years, but less than 5 years: 0·119; (b) If the warranty against defects covers a period of at least 5 years: 0·238. 15A–15G Regional factor: (a) If the prescribed activity is undertaken in metropolitan Victoria: 1·05; (b) If the prescribed activity is undertaken in regional Victoria—climatic region Mild: 0·84; (c) If the prescribed activity is undertaken in regional Victoria—climatic region Cold: 1·32; (d) If the prescribed activity is undertaken in regional Victoria—climatic region Hot: 0·69. 15H Regional factor: (a) If the prescribed activity is undertaken in metropolitan Victoria: 1·05; (b) If the prescribed activity is undertaken in regional Victoria—climatic region Mild: 0·84; (c) If the prescribed activity is undertaken in regional Victoria—climatic region Cold: 1·93; (d) If the prescribed activity is undertaken in regional Victoria—climatic region Hot: 0·78. Authorised by the Chief Parliamentary Counsel 78 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 15—Weather sealing Part C—Time at which activity undertaken and reduction in greenhouse gas emissions occurs The time at which the activity is taken to have been undertaken, and the time at which the reduction in greenhouse gas emissions resulting from that activity is taken to have occurred, is— (a) if one or more products referred to in item 15C of Part A is installed as part of the activity, the beginning of whichever of the following days is later— (i) the day on which the last of those products in installed; (ii) the day of the decommissioning of the last of the ceiling or wall exhaust fans in place of which those products were installed; or (b) otherwise, the beginning of the day on which the last of the products or combinations of products is installed as part of the activity. * * * * * Sch. 16 revoked by S.R. No. 127/2010 reg. 11. Authorised by the Chief Parliamentary Counsel 79 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 17—Low flow shower rose Sch. 17 amended by Schedule 17—Low flow shower rose S.R. Nos Regulation 6(1)(n) 146/2011 reg. 20, 6/2012 Prescribed activity under regulation 6(1)(n): Decommissioning a non-low reg. 24(a)(b). flow shower rose (not being a shower rose rated as having a 3 star or higher water efficiency when assessed and labelled in accordance with AS/NZS 6400:2005 reissued in December 2006) and installing a low flow shower rose that complies with the criteria specified in Part A of Schedule 17. Part A—Criteria Item 17A A product complying with the requirements of AS/NZS 3662:2005 and that achieves a minimum 3 star rating when assessed and labelled in accordance with AS/NZS 6400:2005. Sch. 17 Pt B amended by Part B—Calculation of carbon dioxide S.R. Nos 6/2012 equivalents of greenhouse gases reg. 24(c), 32/2012 The carbon dioxide equivalent (in tonnes) of greenhouse gases reg. 26. to be reduced by the decommissioning of a non-low flow shower rose and the installation of a product referred to in an item in Part A is calculated by multiplying the number of products installed (not being more than 2 if installed in residential premises) by the abatement factor for that item and multiplying the result by the regional factor applying to the place where the product is installed. The following are the abatement factors and regional factors for each item in Part A: Item 17A Abatement factor: 2⋅14. Authorised by the Chief Parliamentary Counsel 80 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008

Schedule 17—Low flow shower rose 17A Regional factor: (a) If the product is installed in metropolitan Victoria: 0⋅85; (b) If the product is installed in regional Victoria: 1·40. Sch. 17 Pt C Part C—Time at which activity undertaken (Heading) substituted by and reduction in greenhouse gas emissions S.R. No. 96/2013 reg. 8. occurs Item 17A At the beginning of the day which is the later of the day on which the installation of the product is completed and the day on which the non-low flow shower rose is decommissioned. * * * * * Sch. 18 revoked by S.R. No. 127/2010 reg. 11. Authorised by the Chief Parliamentary Counsel 81 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 19—Destruction of pre-1996 refrigerator or freezer Sch. 19 amended by Schedule 19—Destruction of pre-1996 S.R. Nos 146/2011 refrigerator or freezer reg. 21, 6/2012 Regulation 6(1)(o) reg. 25. Prescribed activity under regulation 6(1)(o): Removing from the premises a refrigerator or freezer manufactured before 1996 and in working order and destroying the refrigerator or freezer in accordance with the criteria specified in Part A of Schedule 19. Sch. 19 Pt A amended by Part A—Criteria S.R. No. 32/2012 Item reg. 27(a). 19A Destruction by the disposal, in accordance with the Ozone Protection and Synthetic Greenhouse Gas Management Act 1989 of the Commonwealth, of scheduled substances (within the meaning of that Act) contained in the refrigerator or freezer manufactured before 1996 and removed from the premises. Sch. 19 Pt B amended by Part B—Calculation of carbon dioxide S.R. No. 32/2012 equivalents of greenhouse gases reg. 27(b)(c). The carbon dioxide equivalent (in tonnes) of greenhouse gases to be reduced by the removal and destruction of an item referred to in Part A is calculated by multiplying the abatement factor for that item by the regional factor applying to the place where the premises from which the item is removed is situated. The following are the abatement factors and regional factors for each item in Part A: Item 19A Abatement factor: (a) Single door refrigerator or freezer: 3⋅25; (b) Two door refrigerator or freezer: 5⋅82. Authorised by the Chief Parliamentary Counsel 82 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008

Schedule 19—Destruction of pre-1996 refrigerator or freezer 19A Regional factor: (a) If the premises from which the item is removed are in metropolitan Victoria: 0⋅98; (b) If the premises from which the item is removed are in regional Victoria: 1⋅04. Sch. 19 Pt C Part C—Time at which activity (Heading) substituted by undertaken and reduction in greenhouse S.R. No. 96/2013 reg. 8. gas emissions occurs Sch. 19 Pt C Item amended by S.R. No. 19A At the beginning of the day which is the later of the day on 32/2012 which the refrigerator or freezer is removed from the reg. 27(d). premises and the day on which it is destroyed. Authorised by the Chief Parliamentary Counsel 83 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 20—High efficiency ducted gas heater Sch. 20 revoked by Schedule 20—High efficiency S.R. No. 127/2010 ducted gas heater reg. 12, Regulation 6(1)(p) new Sch. 20 inserted by S.R. No. Prescribed activity under regulation 6(1)(p): Installing a high efficiency 127/2010 ducted gas heater that complies with the criteria specified in Part A of reg. 13, Schedule 20 in premises where no other central heating or cooling product amended by S.R. Nos is installed. 6/2012 reg. 26, 24/2013 reg. 8. Part A—Criteria Item 20A Ducted gas heater certified by an accredited body to achieve a minimum 5 star rating when tested and rated in accordance with AS 4556–2000 with a minimum rated output heating capacity of 10 kW as determined in accordance with AS 4556–2000 and listed in the ESC register. Sch. 20 Pt B amended by Part B—Calculation of carbon dioxide S.R. No. 32/2012 equivalents of greenhouse gases reg. 28. The carbon dioxide equivalent (in tonnes) of greenhouse gases to be reduced by the installation of a product referred to in an item in Part A is calculated by multiplying the abatement factor for that item by the regional factor applying to the place where the product is installed. The following are the abatement factors and regional factors for each item in Part A: Item 20A Abatement factor: (a) if the product has a rated output heating capacity of not less than 10 and not more than 18 kW as determined in accordance with AS 4556–2000 and has a star rating determined in accordance with AS 4556–2000 of— Authorised by the Chief Parliamentary Counsel 84 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 20—High efficiency ducted gas heater (i) not less than 5 and not more than 5·49: 4·12; (ii) 5·5 or more: 4·99; (b) if the product has a rated output heating capacity of more than 18 and not more than 28 kW as determined in accordance with AS 4556–2000 and has a star rating determined in accordance with AS 4556–2000 of— (i) not less than 5 and not more than 5·49: 4·30; (ii) 5·5 or more: 5·20; (c) if the product has a rated output heating capacity of more than 28 kW as determined in accordance with AS 4556–2000 and has a star rating determined in accordance with AS 4556–2000 of— (i) not less than 5 and not more than 5·49: 5·92; (ii) 5·5 or more: 7·16. 20A Regional factor: (a) If the product is installed in metropolitan Victoria: 1·00; (b) If the product is installed in regional Victoria—climatic region Mild: 1·00; (c) If the product is installed in regional Victoria—climatic region Cold: 1·61; (d) If the product is installed in regional Victoria—climatic region Hot: 0·71. Authorised by the Chief Parliamentary Counsel 85 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 20—High efficiency ducted gas heater Sch. 20 Pt C (Heading) Part C—Time at which activity substituted by S.R. No. undertaken and reduction in greenhouse 96/2013 reg. 8. gas emissions occurs Item 20A At the beginning of the day on which the installed product is first able to produce and deliver ducted gas heating. Authorised by the Chief Parliamentary Counsel 86 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 21—Incandescent lighting Schedule 21—Incandescent lighting Sch. 21 (Heading) Regulation 6(1)(q) substituted by S.R. No. Prescribed activity under regulation 6(1)(q): Installing lamps that comply 32/2012 with the criteria specified in Part A of Schedule 21 in place of incandescent reg. 29(1). lamps that do not comply with those criteria and decommissioning the Sch. 21 non-complying lamps. inserted by S.R. No. 127/2010 Part A—Criteria reg. 13, amended by S.R. Nos Item 146/2011 reg. 22(a)(b), 21A Installation of low energy GLS (general lighting service) 6/2012 reg. 27. lamp in place of a mains voltage incandescent GLS lamp of at least 25 watts (tungsten filament type) or 18 watts (tungsten halogen type), being a product that— (a) has a light output equivalent to the replaced lamp; and (b) if the product is a compact fluorescent lamp, complies with MEPS in accordance with AS/NZS 4847.2:2010; and (c) if the product is not a compact fluorescent lamp and Sch. 21 Pt A item 21A(c) meets the following requirements— substituted by S.R. No. (i) the compliance requirements for compact 167/2015 reg. 18(1)(a). fluorescent lamps set out in Table 1 of AS/NZS 4847.2:2010; or (ii) if the ESC register indicates that different requirements are to apply to the product, the performance requirements specified for the product on the ESC's Internet site; and (d) achieves minimum lighting source efficacy levels of— (i) 40 lumens/watt where light output is less than 350 lumens; or (ii) 45 lumens/watt where light output is 350 lumens or more and less than 650 lumens; or Authorised by the Chief Parliamentary Counsel 87 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 21—Incandescent lighting (iii) 52 lumens/watt where light output is 650 lumens or more and less than 850 lumens; or (iv) 55 lumens/watt where light output is 850 lumens or more; and (e) if the lamp is to be installed in a dimmable circuit, is approved by the manufacturer as suitable for such a circuit; and (f) has a minimum manufacturer's rated lifetime of 8000 hours; and Sch. 21 Pt A (g) has a colour temperature that is, or is capable of item 21A(g) substituted by being set to, warm white (2700K to 3500K) or cool S.R. No. white (3500K to 4000K); and 167/2015 reg. 18(1)(b). Sch. 21 Pt A (h) is listed in the ESC register. item 21A(h) inserted by S.R. No. 167/2015 reg. 18(1)(b). 21B Installation of low energy reflector lamp in place of a mains voltage incandescent reflector lamp, being a product that— (a) has a light output equivalent to the replaced lamp; and Sch. 21 Pt A (b) meets the following requirements— item 21B(b) substituted by S.R. No. (i) the compliance requirements for compact 167/2015 fluorescent lamps set out in Table 1 of reg. 18(2)(a). AS/NZS 4847.2:2010; or (ii) if the ESC register indicates that different requirements are to apply to the product, the performance requirements specified for the product on the ESC's Internet site; and Authorised by the Chief Parliamentary Counsel 88 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 21—Incandescent lighting (c) achieves minimum lighting source efficacy levels of Sch. 21 Pt A 45 lumens/watt; and item 21B(c) amended by S.R. No. 167/2015 reg. 18(2)(b). (d) has a minimum manufacturer's rated lifetime of Sch. 21 Pt A item 21B(d) 12 000 hours; and amended by S.R. No. 167/2015 reg. 18(2)(c). (e) if the lamp is to be installed in a dimmable circuit, is approved by the manufacturer as suitable for such a circuit; and (f) has a colour temperature that is, or is capable of Sch. 21 Pt A item 21B(f) being set to, warm white (2700K to 3500K) or cool amended by white (3500K to 4000K). S.R. No. 167/2015 reg. 18(2)(d). 21C Installation of low energy lamp in place of an existing 12 volt halogen lamp of at least 35 watts being a product that is compatible with the type of transformer or converter used with the replaced halogen lamp and that— (a) if the lamp is to be installed in a dimmable circuit, is approved by the manufacturer as suitable for such a circuit; and (b) has the following characteristics— (i) the compliance requirements for compact Sch. 21 Pt A item 21C(b)(i) fluorescent lamps set out in Table 1 of substituted by AS/NZS 4847.2:2010 or, if the ESC register S.R. No. 167/2015 indicates that different requirements are to reg. 18(3)(a). apply to the product, the performance requirements specified for the product on the ESC's Internet site; and Authorised by the Chief Parliamentary Counsel 89 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 21—Incandescent lighting Sch. 21 Pt A (ii) achieves minimum lighting source efficacy item 21C(b)(ii) levels of 52 lumens/watt; and amended by S.R. No. 167/2015 reg. 18(3)(b). Sch. 21 Pt A (iii) has a minimum light output of 420 lumens in item 21C(b)(iii) amended by the forward direction; and S.R. No. 167/2015 reg. 18(3)(c). Sch. 21 Pt A (iv) has a minimum manufacturer's rated lifetime item 21C(b)(iv) amended by of 15 000 hours; and S.R. No. 167/2015 reg. 18(3)(d). Sch. 21 Pt A (v) has a colour temperature that is, or is capable item 21C(b)(v) amended by of being set to, warm white (2700K to 3500K) S.R. No. or cool white (3500K to 4000K); and 167/2015 reg. 18(3)(e). Sch. 21 Pt A (vi) in the case of a product installed in residential item 21C(b)(vi) amended by premises, has a beam angle of not less than S.R. No. 50 degrees when determined in accordance 146/2011 reg. 22(c), with IEC/TR 61341 Edition 2.0; and substituted by S.R. No. 167/2015 reg. 18(3)(f). Sch. 21 Pt A (c) is listed in the ESC register. item 21C(c) inserted by S.R. No. 167/2015 reg. 18(3)(g). 21D Installation of a mains voltage low energy downlight fitting in place of an existing 12 volt halogen downlight fitting that uses a 12 volt halogen lamp of at least 35 watts, being a product that— Authorised by the Chief Parliamentary Counsel 90 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 21—Incandescent lighting (a) if the downlight fitting and lamp are to be installed in a dimmable circuit, is approved by the manufacturer as suitable for such a circuit; and (b) uses a lamp that has the following characteristics— (i) the compliance requirements for compact Sch. 21 Pt A item 21D(b)(i) fluorescent lamps set out in Table 1 of substituted by AS/NZS 4847.2:2010 or, if the ESC register S.R. No. 167/2015 indicates that different requirements are to reg. 18(4)(a)(i). apply to the product, the performance requirements specified for the product on the ESC's Internet site; and (ii) achieves a minimum lighting source efficacy Sch. 21 Pt A item 21D(b)(ii) of 48 lumens/watt; and amended by S.R. No. 167/2015 reg. 18 (4)(a)(ii). (iii) has a minimum light output of 400 lumens in Sch. 21 Pt A item 21D(b)(iii) the forward direction; and amended by S.R. Nos 146/2011 reg. 22(d), 167/2015 reg. 18 (4)(a)(iii). (iv) has a minimum manufacturer's rated lifetime Sch. 21 Pt A item 21D(b)(iv) of 15 000 hours; and amended by S.R. No. 167/2015 reg. 18 (4)(a)(iv). (v) has a colour temperature that is, or is capable Sch. 21 Pt A item 21D(b)(v) of being set to, warm white (2700K to 3500K) amended by or cool white (3500K to 4000K); and S.R. No. 167/2015 reg. 18 (4)(a)(v). Authorised by the Chief Parliamentary Counsel 91 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 21—Incandescent lighting Sch. 21 Pt A (vi) in the case of a product installed in residential item 21D(b)(vi) premises, has a beam angle of not less than amended by S.R. No. 40 degrees when determined in accordance 146/2011 with IEC/TR 61341 Edition 2.0; and reg. 22(e), substituted by S.R. No. 167/2015 reg. 18 (4)(a)(vi). Sch. 21 Pt A (c) is listed in the ESC register. item 21D(c) inserted by S.R. No. 167/2015 reg. 18(4)(b). Sch. 21 Pt A 21E Installation, in place of a mains voltage halogen lamp of at item 21E inserted by least 35 watts with a GU10 base, of a low energy lamp S.R. No. that— 167/2015 reg. 17(1). (a) has a GU10 base; and (b) meets the following requirements— (i) the compliance requirements for compact fluorescent lamps set out in Table 1 of AS/NZS 4847.2:2010; or (ii) if the ESC register indicates that different requirements are to apply to the lamp, the performance requirements specified for the lamp on the ESC's Internet site; and (c) achieves a minimum lighting source efficacy of 48 lumens/watt; and (d) has a minimum light output of 400 lumens in the forward direction; and (e) has a minimum manufacturer's rated lifetime of 15 000 hours; and (f) has a colour temperature that is, or is capable of being set to, warm white (2700K to 3500K) or cool white (3500K to 4000K); and Authorised by the Chief Parliamentary Counsel 92 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 21—Incandescent lighting (g) if the lamp is to be installed in a dimmable circuit, is approved by the manufacturer as suitable for a dimmable circuit; and (h) if the lamp is to be installed in residential premises, has a beam angle of not less than 36 degrees when determined in accordance with IEC/TR 61341 Edition 2.0; and (i) is listed in the ESC register. 21F Installation, in place of an existing mains voltage halogen Sch. 21 Pt A item 21F downlight fitting that uses a halogen lamp with a inserted by GU10 base of at least 35 watts, of a mains voltage low S.R. No. 16/2016 energy downlight fitting that— reg. 7(1). (a) uses a lamp that— (i) meets the following requirements— (A) the compliance requirements for compact fluorescent lamps set out in Table 1 of AS/NZS 4847.2:2010; or (B) if the ESC register indicates that different requirements are to apply to the lamp, the performance requirements specified for the lamp on the ESC's Internet site; and (ii) achieves a minimum lighting source efficacy of 48 lumens/watt; and (iii) has a minimum light output of 400 lumens in the forward direction; and (iv) has a minimum manufacturer's rated lifetime of 15 000 hours; and (v) has a colour temperature that is, or is capable of being set to, warm white (2700K to 3500K) or cool white (3500K to 4000K); and (b) if the fitting and lamp are to be installed in a dimmable circuit, is approved by the manufacturer as suitable for a dimmable circuit; and Authorised by the Chief Parliamentary Counsel 93 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 21—Incandescent lighting (c) if the fitting and lamp are to be installed in residential premises, has a beam angle of not less than 36 degrees when determined in accordance with IEC/TR 61341 Edition 2.0; and (d) is listed in the ESC register. Sch. 21 Pt B amended by S.R. No. Part B—Calculation of carbon dioxide 32/2012 reg. 29(2). equivalents of greenhouse gases The carbon dioxide equivalent (in tonnes) of greenhouse gases to be reduced by the installation of a product or products referred to in an item in Part A is the sum of the figures obtained by multiplying the number of lamps installed in the premises under each item in Part A by the abatement factor for that item by the PF multiplier for that item and by the regional factor applying to the place where the product or products are installed. The following are the abatement factors, PF multipliers and regional factors for each item in Part A: Item 21A Abatement factor: (a) The abatement factor for a product that achieves a minimum lighting source efficacy of— (i) 40 lumens/watt where light output is less than 350 lumens; or (ii) 45 lumens/watt where light output is 350 lumens or more and less than 650 lumens; or (iii) 52 lumens/watt where light output is 650 lumens or more and less than 850 lumens; or (iv) 55 lumens/watt where light output is 850 lumens or more— and has a manufacturer's rated lifetime of a number of hours in the range specified, in respect of an item, in column 2 of the following Table is the factor Authorised by the Chief Parliamentary Counsel 94 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 21—Incandescent lighting shown in column 3 of that Table in respect of that item. Column 1 Column 2 Column 3 Sch. 21 Pt B item 21A(a) Abatement (Table) Item Hours factor amended by S.R. No. 1 8000 or more and less 0∙20 167/2015 than 10 000 reg. 18(5)(a). 2 10 000 or more and less 0∙25 than 12 000 3 12 000 or more and less 0∙30 than 15 000 4 15 000 or more and less 0∙37 than 20 000 5 20 000 or more and less 0∙50 than 25 000 6 25 000 or more 0∙62 (b) The abatement factor for a product that achieves a minimum lighting source efficacy of— (i) 48 lumens/watt where light output is less than 350 lumens; or (ii) 54 lumens/watt where light output is 350 lumens or more and less than 650 lumens; or (iii) 62 lumens/watt where light output is 650 lumens or more and less than 850 lumens; or (iv) 66 lumens/watt where light output is 850 lumens or more— and has a manufacturer's rated lifetime of a number of hours in the range specified, in respect of an item, in column 2 of the following Table is the factor shown in column 3 of that Table in respect of that item. Authorised by the Chief Parliamentary Counsel 95 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 21—Incandescent lighting Sch. 21 Pt B Column 1 Column 2 Column 3 item 21A(b) (Table) Abatement amended by Item Hours factor S.R. No. 167/2015 1 8000 or more and less 0∙22 reg. 18(5)(b). than 10 000 2 10 000 or more and less 0∙27 than 12 000 3 12 000 or more and less 0∙33 than 15 000 4 15 000 or more and less 0∙41 than 20 000 5 20 000 or more and less 0∙55 than 25 000 6 25 000 or more 0∙68 (c) The abatement factor for a product that achieves a minimum lighting source efficacy of— (i) 58 lumens/watt where light output is less than 350 lumens; or (ii) 65 lumens/watt where light output is 350 lumens or more and less than 650 lumens; or (iii) 75 lumens/watt where light output is 650 lumens or more and less than 850 lumens; or (iv) 79 lumens/watt where light output is 850 lumens or more— and has a manufacturer's rated lifetime of a number of hours in the range specified, in respect of an item, in column 2 of the following Table is the factor shown in column 3 of that Table in respect of that item. Authorised by the Chief Parliamentary Counsel 96 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 21—Incandescent lighting Column 1 Column 2 Column 3 Sch. 21 Pt B item 21A(c) Abatement (Table) Item Hours factor amended by S.R. No. 1 8000 or more and less 0∙23 167/2015 than 10 000 reg. 18(5)(c). 2 10 000 or more and less 0∙29 than 12 000 3 12 000 or more and less 0∙34 than 15 000 4 15 000 or more and less 0∙43 than 20 000 5 20 000 or more and less 0∙57 than 25 000 6 25 000 or more 0∙72 (d) The abatement factor for a product that achieves a Sch. 21 Pt B item 21A(d) minimum lighting source efficacy of— inserted by S.R. No. (i) 69 lumens/watt where light output is less than 167/2015 reg. 18(5)(d). 350 lumens; or (ii) 78 lumens/watt where light output is 350 lumens or more and less than 650 lumens; or (iii) 90 lumens/watt where light output is 650 lumens or more and less than 850 lumens; or (iv) 95 lumens/watt where light output is 850 lumens or more— and has a manufacturer's rated lifetime of a number of hours in the range specified, in respect of an item, in column 2 of the following Table is the factor shown in column 3 of that Table in respect of that item. Authorised by the Chief Parliamentary Counsel 97 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 21—Incandescent lighting Column 1 Column 2 Column 3 Abatement Item Hours factor 1 8000 or more and less than 10 000 0∙24 2 10 000 or more and less than 12 000 0∙30 3 12 000 or more and less than 15 000 0∙36 4 15 000 or more and less than 20 000 0∙45 5 20 000 or more and less than 25 000 0∙60 6 25 000 or more 0∙75 Sch. 21 Pt B 21B Abatement factor: item 21B substituted by S.R. No. (a) The abatement factor for a product that achieves a 167/2015 minimum lighting source efficacy of 45 lumens/watt reg. 18(6). and has a manufacturer's rated lifetime of a number of hours in the range specified, in respect of an item, in column 2 of the following Table is the factor shown in column 3 of that Table in respect of that item. Column 1 Column 2 Column 3 Abatement Item Hours factor 1 12 000 or more and less 0∙40 than 15 000 2 15 000 or more and less 0∙50 than 20 000 3 20 000 or more and less 0∙67 than 25 000 4 25 000 or more 0∙83 Authorised by the Chief Parliamentary Counsel 98 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 21—Incandescent lighting (b) The abatement factor for a product that achieves a minimum lighting source efficacy of 54 lumens/watt and has a manufacturer's rated lifetime of a number of hours in the range specified, in respect of an item, in column 2 of the following Table is the factor shown in column 3 of that Table in respect of that item. Column 1 Column 2 Column 3 Abatement Item Hours factor 1 12 000 or more and less 0∙41 than 15 000 2 15 000 or more and less 0∙51 than 20 000 3 20 000 or more and less 0∙68 than 25 000 4 25 000 or more 0∙85 (c) The abatement factor for a product that achieves a minimum lighting source efficacy of 65 lumens/watt and has a manufacturer's rated lifetime of a number of hours in the range specified, in respect of an item, in column 2 of the following Table is the factor shown in column 3 of that Table in respect of that item. Column 1 Column 2 Column 3 Abatement Item Hours factor 1 12 000 or more and less 0∙42 than 15 000 2 15 000 or more and less 0∙52 than 20 000 3 20 000 or more and less 0∙70 than 25 000 4 25 000 or more 0∙87 Authorised by the Chief Parliamentary Counsel 99 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 21—Incandescent lighting (d) The abatement factor for a product that achieves a minimum lighting source efficacy of 78 lumens/watt and has a manufacturer's rated lifetime of a number of hours in the range specified, in respect of an item, in column 2 of the following Table is the factor shown in column 3 of that Table in respect of that item. Column 1 Column 2 Column 3 Abatement Item Hours factor 1 12 000 or more and less 0∙42 than 15 000 2 15 000 or more and less 0∙53 than 20 000 3 20 000 or more and less 0∙71 than 25 000 4 25 000 or more 0∙88 Sch. 21 Pt B 21C Abatement factor: item 21C amended by S.R. No. (a) The abatement factor for a product that achieves a 146/2011 minimum lighting source efficacy of 52 lumens/watt reg. 22(f), substituted by or more but less than 62 lumens/watt and has a No. 167/2015 manufacturer's rated lifetime of a number of hours in reg. 18(6). the range specified, in respect of an item, in column 2 of the following Table is the factor shown in column 3 of that Table in respect of that item. Column 1 Column 2 Column 3 Abatement Item Hours factor 1 15 000 or more and less 0∙44 than 20 000 2 20 000 or more and less 0∙59 than 25 000 3 25 000 or more 0∙74 Authorised by the Chief Parliamentary Counsel 100 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 21—Incandescent lighting (b) The abatement factor for a product that achieves a minimum lighting source efficacy of 62 lumens/watt or more but less than 75 lumens/watt and has a manufacturer's rated lifetime of a number of hours in the range specified, in respect of an item, in column 2 of the following Table is the factor shown in column 3 of that Table in respect of that item. Column 1 Column 2 Column 3 Abatement Item Hours factor 1 15 000 or more and less 0∙47 than 20 000 2 20 000 or more and less 0∙63 than 25 000 3 25 000 or more 0∙78 (c) The abatement factor for a product that achieves a minimum lighting source efficacy of 75 lumens/watt or more but less than 90 lumens/watt and has a manufacturer's rated lifetime of a number of hours in the range specified, in respect of an item, in column 2 of the following Table is the factor shown in column 3 of that Table in respect of that item. Column 1 Column 2 Column 3 Abatement Item Hours factor 1 15 000 or more and less 0∙49 than 20 000 2 20 000 or more and less 0∙66 than 25 000 3 25 000 or more 0∙82 Authorised by the Chief Parliamentary Counsel 101 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 21—Incandescent lighting (d) The abatement factor for a product that achieves a minimum lighting source efficacy of 90 lumens/watt or more and has a manufacturer's rated lifetime of a number of hours in the range specified, in respect of an item, in column 2 of the following Table is the factor shown in column 3 of that Table in respect of that item. Column 1 Column 2 Column 3 Abatement Item Hours factor 1 15 000 or more and less 0∙51 than 20 000 2 20 000 or more and less 0∙68 than 25 000 3 25 000 or more 0∙85 Sch. 21 Pt B 21D Abatement factor: item 21D amended by S.R. No. (a) The abatement factor for a product that achieves a 146/2011 minimum lighting source efficacy of 48 lumens/watt reg. 22(g), substituted by or more but less than 58 lumens/watt and has a No. 167/2015 manufacturer's rated lifetime of a number of hours in reg. 18(6). the range specified, in respect of an item, in column 2 of the following Table is the factor shown in column 3 of that Table in respect of that item. Column 1 Column 2 Column 3 Abatement Item Hours factor 1 15 000 or more and less 0∙46 than 20 000 2 20 000 or more and less 0∙61 than 25 000 3 25 000 or more 0∙76 Authorised by the Chief Parliamentary Counsel 102 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 21—Incandescent lighting (b) The abatement factor for a product that achieves a minimum lighting source efficacy of 58 lumens/watt or more but less than 69 lumens/watt and has a manufacturer's rated lifetime of a number of hours in the range specified, in respect of an item, in column 2 of the following Table is the factor shown in column 3 of that Table in respect of that item. Column 1 Column 2 Column 3 Abatement Item Hours factor 1 15 000 or more and less 0∙48 than 20 000 2 20 000 or more and less 0∙64 than 25 000 3 25 000 or more 0∙80 (c) The abatement factor for a product that achieves a minimum lighting source efficacy of 69 lumens/watt or more but less than 83 lumens/watt and has a manufacturer's rated lifetime of a number of hours in the range specified, in respect of an item, in column 2 of the following Table is the factor shown in column 3 of that Table in respect of that item. Column 1 Column 2 Column 3 Abatement Item Hours factor 1 15 000 or more and less 0∙50 than 20 000 2 20 000 or more and less 0∙67 than 25 000 3 25 000 or more 0∙83 Authorised by the Chief Parliamentary Counsel 103 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 21—Incandescent lighting (d) The abatement factor for a product that achieves a minimum lighting source efficacy of 83 lumens/watt or more but less than 100 lumens/watt and has a manufacturer's rated lifetime of a number of hours in the range specified, in respect of an item, in column 2 of the following Table is the factor shown in column 3 of that Table in respect of that item. Column 1 Column 2 Column 3 Abatement Item Hours factor 1 15 000 or more and less 0∙52 than 20 000 2 20 000 or more and less 0∙69 than 25 000 3 25 000 or more 0∙86 (e) The abatement factor for a product that achieves a minimum lighting source efficacy of 100 lumens/watt or more and has a manufacturer's rated lifetime of a number of hours in the range specified, in respect of an item, in column 2 of the following Table is the factor shown in column 3 of that Table in respect of that item. Column 1 Column 2 Column 3 Abatement Item Hours factor 1 15 000 or more and less 0∙53 than 20 000 2 20 000 or more and less 0∙71 than 25 000 3 25 000 or more 0∙88 Authorised by the Chief Parliamentary Counsel 104 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 21—Incandescent lighting 21E-21F Abatement factor: Sch. 21 Pt B item 21E (a) The abatement factor for a product that achieves a Abatement minimum lighting source efficacy of 48 lumens/watt factor: (Heading) or more but less than 58 lumens/watt and has a substituted as manufacturer's rated lifetime of a number of hours in item 21E-21F Abatement the range specified, in respect of an item, in factor: column 2 of the following Table is the factor shown (heading) by S.R. No. in column 3 of that Table in respect of that item. 16/2016 reg. 7(2)(a). Column 1 Column 2 Column 3 Sch. 21 Pt B Abatement item 21E Item Hours factor inserted by S.R. No. 1 15 000 or more and less 167/2015 0⋅56 reg. 17(2). than 20 000 2 20 000 or more and less 0⋅74 than 25 000 3 25 000 or more 0⋅93 (b) The abatement factor for a product that achieves a minimum lighting source efficacy of 58 lumens/watt or more but less than 69 lumens/watt and has a manufacturer's rated lifetime of a number of hours in the range specified, in respect of an item, in column 2 of the following Table is the factor shown in column 3 of that Table in respect of that item. Column 1 Column 2 Column 3 Abatement Item Hours factor 1 15 000 or more and less 0⋅58 than 20 000 2 20 000 or more and less 0⋅78 than 25 000 3 25 000 or more 0⋅97 Authorised by the Chief Parliamentary Counsel 105 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 21—Incandescent lighting (c) The abatement factor for a product that achieves a minimum lighting source efficacy of 69 lumens/watt or more but less than 83 lumens/watt and has a manufacturer's rated lifetime of a number of hours in the range specified, in respect of an item, in column 2 of the following Table is the factor shown in column 3 of that Table in respect of that item. Column 1 Column 2 Column 3 Abatement Item Hours factor 1 15 000 or more and less 0⋅60 than 20 000 2 20 000 or more and less 0⋅80 than 25 000 3 25 000 or more 1⋅00 (d) The abatement factor for a product that achieves a minimum lighting source efficacy of 83 lumens/watt or more but less than 100 lumens/watt and has a manufacturer's rated lifetime of a number of hours in the range specified, in respect of an item, in column 2 of the following Table is the factor shown in column 3 of that Table in respect of that item. Column 1 Column 2 Column 3 Abatement Item Hours factor 1 15 000 or more and less 0⋅62 than 20 000 2 20 000 or more and less 0⋅82 than 25 000 3 25 000 or more 1⋅03 Authorised by the Chief Parliamentary Counsel 106 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 21—Incandescent lighting (e) The abatement factor for a product that achieves a minimum lighting source efficacy of 100 lumens/watt or more and has a manufacturer's rated lifetime of a number of hours in the range specified, in respect of an item, in column 2 of the following Table is the factor shown in column 3 of that Table in respect of that item. Column 1 Column 2 Column 3 Abatement Item Hours factor 1 15 000 or more and less 0⋅63 than 20 000 2 20 000 or more and less 0⋅84 than 25 000 3 25 000 or more 1⋅05 21A-21F PF multiplier: Sch. 21 Pt B item 21A–21D PF multiplier: (a) If the power factor of the product determined (Heading) in accordance with AS/NZS 4847.1:2010 is substituted as Sch. 21 Pt B less than 0·9: 1·00; item 21A–21E PF multiplier: (b) If the power factor of the product determined (Heading) by in accordance with AS/NZS 4847.1:2010 is S.R. No. 167/2015 0·9 or more: 1·05. reg. 17(3)(a), substituted as 21A-21F multiplier: (Heading) by S.R. No. 16/2016 reg. 7(2)(b). Authorised by the Chief Parliamentary Counsel 107 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 21—Incandescent lighting Sch. 21 Pt B 21A-21F Regional factor: item 21A–21D Regional (a) If the product or products are installed in factor: metropolitan Victoria: 0·98; (Heading) substituted as Sch. 21 Pt B (b) If the product or products are installed in item 21A–21E regional Victoria: 1·04. Regional factor: (Heading) by S.R. No. 167/2015 reg. 17(3)(b), substituted as Sch. 21 Pt B item 21A-21F: Regional factor: (Heading) by S.R. No. 16/2016 reg. 7(2)(c). Sch. 21 Pt C (Heading) Part C—Time at which activity substituted by S.R. No. undertaken and reduction in greenhouse 96/2013 reg. 8. gas emissions occurs Item Sch. 21 Pt C 21A-21F At the beginning of the day which is the later of the item 21A–21D (Heading) day on which the installation of the product or substituted as products is completed and the day on which the Sch. 21 Pt C item 21A–21E replaced lamps are decommissioned. (Heading) by S.R. No. 167/2015 reg. 17(4), substituted as item 21A-21F: (Heading) by S.R. No. 16/2016 reg. 7(3). Authorised by the Chief Parliamentary Counsel 108 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 22—High efficiency refrigerators and freezers Schedule 22—High efficiency Sch. 22 inserted by refrigerators and freezers S.R. No. 127/2010 Regulation 6(1)(r) reg. 13, amended by Prescribed activity under regulation 6(1)(r): Installing a high efficiency S.R. Nos refrigerator or high efficiency freezer that complies with the criteria specified 146/2011 reg. 23, 6/2012 in Part A of Schedule 22. reg. 28. Part A—Criteria Item 22A Single door refrigerator listed in the ESC register— (a) being a Group 1 refrigerator as defined by AS/NZS 4474.1:1997 or AS/NZS 4474.1:2007; and (b) having a total volume as determined in accordance with AS/NZS 4474.1:1997 or AS/NZS 4474.1:2007 of not less than 100 litres and not more than 500 litres; and (c) having a minimum star rating index of 2·0 as determined in accordance with AS/NZS 4474.2:2009. 22B Two door refrigerator listed in the ESC register— (a) being a Group 4, 5B, 5S or 5T refrigerator as defined by AS/NZS 4474.1:1997 or AS/NZS 4474.1:2007; and (b) having a total volume as determined in accordance with AS/NZS 4474.1:1997 or AS/NZS 4474.1:2007 of not less than 100 litres and not more than 700 litres; and (c) having a minimum star rating index of 2·7 as determined in accordance with AS/NZS 4474.2:2009. 22C Chest freezer listed in the ESC register— (a) being a Group 6C product as defined by AS/NZS 4474.1:1997 or AS/NZS 4474.1:2007; and Authorised by the Chief Parliamentary Counsel 109 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 22—High efficiency refrigerators and freezers (b) having a total volume as determined in accordance with AS/NZS 4474.1:1997 or AS/NZS 4474.1:2007 of not less than 100 litres and not more than 700 litres; and (c) having a minimum star rating index of 3·3 as determined in accordance with AS/NZS 4474.2:2009. 22D Upright freezer listed in the ESC register— (a) being a Group 6U or 7 product as defined by AS/NZS 4474.1:1997 or AS/NZS 4474.1:2007; and (b) having a total volume as determined in accordance with AS/NZS 4474.1:1997 or AS/NZS 4474.1:2007 of not less than 100 litres and not more than 400 litres; and (c) having a minimum star rating index of 2·5 as determined in accordance with AS/NZS 4474.2:2009. Sch. 22 Pt B amended by Part B—Calculation of carbon dioxide S.R. No. 32/2012 equivalents of greenhouse gases reg. 30. The carbon dioxide equivalent (in tonnes) of greenhouse gases to be reduced by the installation of a product referred to in an item in Part A is calculated by multiplying the abatement factor for that item by the regional factor applying to the place where the product is installed. The following are the abatement factors and regional factors for each item in Part A: Item 22A Abatement factor: {[0⋅9126 × (200 + 4 × Vff0·67)] – CEC} × 0⋅01392 where Vff is the volume in litres of the fresh food compartment of the product and CEC is the comparative energy consumption specified on the energy rating label as defined by AS/NZS 4474.2:2009. Authorised by the Chief Parliamentary Counsel 110 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 22—High efficiency refrigerators and freezers 22B Abatement factor: {[0⋅6954 × (150 + 8·8 × (Vff + 1⋅6 × Vfr)0·67)] – CEC} × 0⋅01392 where Vff is the volume in litres of the fresh food compartment of the product, Vfr is the volume of the freezer compartment and CEC is the comparative energy consumption specified on the energy rating label as defined by AS/NZS 4474.2:2009. 22C Abatement factor: {[0⋅6329 × (150 + 7⋅5 × (1⋅6 × Vfr)0·67)] – CEC} × 0⋅01719 where Vfr is the volume of the freezer compartment and CEC is the comparative energy consumption specified on the energy rating label as defined by AS/NZS 4474.2:2009. 22D Abatement factor: {[0⋅77 × (150 + 7⋅5 × (1⋅6 × Vfr)0·67)] – CEC} × 0⋅01719 where Vfr is the volume of the freezer compartment and CEC is the comparative energy consumption specified on the energy rating label as defined by AS/NZS 4474.2:2009. 22A–22D Regional factor: (a) If the product is installed in metropolitan Victoria: 0·98; (b) If the product is installed in regional Victoria: 1·04. Sch. 22 Pt C Part C—Time at which activity (Heading) substituted by undertaken and reduction in greenhouse S.R. No. 96/2013 reg. 8. gas emissions occurs Item 22A–22D At the beginning of the day on which the installation of the product is completed. Authorised by the Chief Parliamentary Counsel 111 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 23—Replacement of refrigerative air conditioner with ducted evaporative cooler Sch. 23 inserted by Schedule 23—Replacement of refrigerative S.R. No. 127/2010 air conditioner with ducted evaporative reg. 13, amended by cooler S.R. No. Regulation 6(1)(s) 6/2012 reg. 29. Prescribed activity under regulation 6(1)(s): Installing a ducted evaporative cooler that complies with the criteria specified in Part A of Schedule 23 after decommissioning a refrigerative air conditioner (whether or not ducted) that was not located in the rooms specified in regulation 6(1)(s)(i) or (ii). Part A—Criteria Item 23A Installing a ducted evaporative cooler, being a product that— (a) complies with and is tested in accordance with AS 2913–2000; and (b) has a minimum effective energy efficiency ratio (EER) of 14 based on measurements of nominal rating (kW) and electricity consumption undertaken according to AS 2913–2000 and calculated according to the formula— EER = 0·2 × EERFL + 0·3 × EER50% + 0·5 × EER20% where— EERFL is the nominal rating (kW) divided by electricity consumption (kW) at rated airflow; EER50% is the nominal rating (kW) divided by electricity consumption (kW) at 50% rated airflow; EER20% is the nominal rating (kW) divided by electricity consumption (kW) at 20% rated airflow. Authorised by the Chief Parliamentary Counsel 112 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 23—Replacement of refrigerative air conditioner with ducted evaporative cooler Part B—Calculation of carbon dioxide Sch. 23 Pt B amended by equivalents of greenhouse gases S.R. No. 32/2012 The carbon dioxide equivalent (in tonnes) of greenhouse gases reg. 31. to be reduced by the installation of a product referred to in an item in Part A is calculated by multiplying the abatement factor for that item by the regional factor applying to the place where the product is installed. The following are the abatement factors and regional factors for each item in Part A: Item 23A Abatement factor: (1) In the case of replacement of a non-ducted refrigerative system— (a) the product has a nominal rating at full load of not less than 7 and not more than 10 kW as determined in accordance with AS 2913–2000 and an effective energy efficiency ratio of— (i) 14 or more and less than 20: 2·6; (ii) 20 or more and less than 30: 3·0; (iii) 30 or more and less than 40: 3·4; (iv) 40 or more: 3·5; (b) if the product has a nominal rating at full load of more than 10 and not more than 13 kW as determined in accordance with AS 2913–2000 and an effective energy efficiency ratio of— (i) 14 or more and less than 20: 4·3; (ii) 20 or more and less than 30: 5·1; (iii) 30 or more and less than 40: 5·6; (iv) 40 or more: 5·9; Authorised by the Chief Parliamentary Counsel 113 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 23—Replacement of refrigerative air conditioner with ducted evaporative cooler (c) if the product has a nominal rating at full load of more than 13 kW as determined in accordance with AS 2913–2000 and an effective energy efficiency ratio of— (i) 14 or more and less than 20: 6·5; (ii) 20 or more and less than 30: 7·6; (iii) 30 or more and less than 40: 8·4; (iv) 40 or more: 8·8. (2) In the case of a replacement of a ducted refrigerative system— (a) if the product has a nominal rating at full load of not less than 7 and not more than 10 kW as determined in accordance with AS 2913–2000 and an effective energy efficiency ratio of— (i) 14 or more and less than 20: 5·7; (ii) 20 or more and less than 30: 6·2; (iii) 30 or more and less than 40: 6·5; (iv) 40 or more: 6·7; (b) if the product has a nominal rating at full load of more than 10 and not more than 13 kW as determined in accordance with AS 2913–2000 and an effective energy efficiency ratio of— (i) 14 or more and less than 20: 9·6; (ii) 20 or more and less than 30: 10·3; (iii) 30 or more and less than 40: 10·8; (iv) 40 or more: 11·1; Authorised by the Chief Parliamentary Counsel 114 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 23—Replacement of refrigerative air conditioner with ducted evaporative cooler (c) if the product has a nominal rating at full load of more than 13 kW as determined in accordance with AS 2913–2000 and an effective energy efficiency ratio of— (i) 14 or more and less than 20: 14·4; (ii) 20 or more and less than 30: 15·4; (iii) 30 or more and less than 40: 16·3; (iv) 40 or more: 16·7. 23A Regional factor: (a) If the product is installed in metropolitan Victoria: 1·00; (b) If the product is installed in regional Victoria—climatic region Mild: 1·06; (c) If the product is installed in regional Victoria—climatic region Cold— (i) in the case of replacement of a non-ducted system: 0·64; (ii) in the case of replacement of a ducted system: 0·86; (d) If the product is installed in regional Victoria—climatic region Hot— (i) in the case of replacement of a non-ducted system: 2·40; (ii) in the case of replacement of a ducted system: 2·35. Authorised by the Chief Parliamentary Counsel 115 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 23—Replacement of refrigerative air conditioner with ducted evaporative cooler Sch. 23 Pt C (Heading) Part C—Time at which activity substituted by S.R. No. undertaken and reduction in greenhouse 96/2013 reg. 8. gas emissions occurs Item 23A At the beginning of the day on which the installed product is first able to produce and deliver evaporative cooling. Authorised by the Chief Parliamentary Counsel 116 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 24—Installation of high efficiency television Schedule 24—Installation of high Sch. 24 inserted by efficiency television S.R. No. 127/2010 Regulation 6(1)(t) reg. 13, amended by Prescribed activity under regulation 6(1)(t): Installing a high efficiency S.R. Nos television that complies with the criteria specified in Part A of Schedule 24. 146/2011 reg. 24, 6/2012 reg. 30. Part A—Criteria Item 24A A product that— (a) is registered for energy labelling in accordance with Sch. 24 Pt A item 24A(a) AS/NZS 62087.2.2:2011; and amended by S.R. No. 147/2016 reg. 4(1)(a). (b) has a minimum star rating of 7 stars as determined in Sch. 24 Pt A item 24A(b) accordance with AS/NZS 62087.2.2:2011; and amended by S.R. No. 147/2016 reg. 4(1)(a)(b). (c) has a Comparative Energy Consumption on the Sch. 24 Pt A item 24A(c) energy rating label of not more than 300 kWh/y. amended by S.R. No. 147/2016 reg. 4(1)(c). Sch. 24 Pt B Part B—Calculation of carbon dioxide amended by S.R. Nos equivalents of greenhouse gases 32/2012 reg. 32, The carbon dioxide equivalent (in tonnes) of greenhouse gases 147/2016 reg. 4(2). to be reduced by the installation of a product referred to in an item in Part A is calculated by multiplying the abatement factor for that item by the regional factor applying to the place where the product is installed. Authorised by the Chief Parliamentary Counsel 117 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 24—Installation of high efficiency television The following are the abatement factors and regional factors for each item in Part A: Item 24A Abatement factor: To be determined in accordance with the formula— [0·32768 × (SA × 0·09344 + 65·408) – CEC] × 0·00964 Where— SA is the area of the screen in cm2 as defined in AS/NZS 62087.2.2:2011; CEC is the comparative energy consumption (kWh/y) specified on the energy rating label as defined by AS/NZS 62087.2.2:2011. 24A Regional factor: (a) If the product is installed in metropolitan Victoria: 0·98; (b) If the product is installed in regional Victoria: 1·04. Sch. 24 Pt C (Heading) Part C—Time at which activity substituted by S.R. No. undertaken and reduction in greenhouse 96/2013 reg. 8. gas emissions occurs Item 24A At the beginning of the day on which the installation of the product is completed. Authorised by the Chief Parliamentary Counsel 118 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 25—Installation of energy efficient (low greenhouse intensity) clothes dryer Schedule 25—Installation of energy efficient Sch. 25 inserted by (low greenhouse intensity) clothes dryer S.R. No. 127/2010 Regulation 6(1)(u) reg. 13, amended by Prescribed activity under regulation 6(1)(u): Installing an energy efficient S.R. No. (low greenhouse intensity) clothes dryer that complies with the criteria 6/2012 reg. 31. specified in Part A of Schedule 25. Part A—Criteria Item 25A A product that is a stand-alone electric clothes dryer (not part of a combination washer/dryer) that is registered for energy labelling in accordance with AS/NZS 2442.2:2000 and achieves a minimum 5 star rating when tested in accordance with AS/NZS 2442.2:2000 and is listed in the ESC register. 25B A stand-alone gas clothes dryer, being a product that is certified by an accredited body as complying with AS 4554–2005 and is listed in the ESC register. Sch. 25 Pt B Part B—Calculation of carbon dioxide amended by S.R. No. equivalents of greenhouse gases 32/2012 reg. 33. The carbon dioxide equivalent (in tonnes) of greenhouse gases to be reduced by the installation of a product referred to in an item in Part A is calculated by multiplying the abatement factor for that item by the regional factor applying to the place where the product is installed. The following are the abatement factors and regional factors for each item in Part A: Item 25A Abatement factor: To be determined in accordance with the formula— (48·08 × R – CEC) × 0·01733 Authorised by the Chief Parliamentary Counsel 119 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 25—Installation of energy efficient (low greenhouse intensity) clothes dryer where— R is the rated capacity of the product in kg as defined by AS/NZS 2442.1:1996; CEC is the comparative energy consumption (kWh/y) specified on the energy rating label as defined by AS/NZS 2442.2:2000. 25B Abatement factor: To be determined in accordance with the formula— R × 0⋅5864 where— R is the drying load of the product in kg as defined by AS 4554–2005. 25A Regional factor: (a) If the product is installed in metropolitan Victoria: 0·98; (b) If the product is installed in regional Victoria: 1·04. 25B Regional factor: (a) If the product is installed in metropolitan Victoria: 0·98; (b) If the product is installed in regional Victoria: 1·05. Sch. 25 Pt C (Heading) Part C—Time at which activity substituted by S.R. No. undertaken and reduction in greenhouse 96/2013 reg. 8. gas emissions occurs Item 25A–25B At the beginning of the day on which the installation of the product is completed. Authorised by the Chief Parliamentary Counsel 120 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 26—Installation of high efficiency pool pump Schedule 26—Installation of high Sch. 26 inserted by efficiency pool pump S.R. No. 127/2010 Regulation 6(1)(v) reg. 13, amended by Prescribed activity under regulation 6(1)(v): Installing a high efficiency pool S.R. No. pump that complies with the criteria specified in Part A of Schedule 26. 6/2012 reg. 32(a)(b). Part A—Criteria Item 26A A product for use with a domestic pool or spa that is a Sch. 26 item 26A single phase, single speed, dual speed, multiple speed or amended by variable speed pump unit with an input power of not less S.R. No. 6/2012 than 100W and not more than 1500W when tested in reg. 32(c). accordance with AS 5102.1–2009 and— (a) is listed as part of a labelling scheme determined in accordance with the Equipment Energy Efficiency (E3) Committee's Voluntary Energy Rating Labelling Program for Swimming Pool Pump-units: Rules for Participation, April 2010, and achieves a minimum 3 star rating when determined in accordance with AS 5102.2–2009; or (b) is registered for energy labelling and achieves a minimum 3 star rating when determined in accordance with AS 5102.2–2009. Sch. 26 Pt B Part B—Calculation of carbon dioxide amended by S.R. No. equivalents of greenhouse gases 32/2012 reg. 34. The carbon dioxide equivalent (in tonnes) of greenhouse gases to be reduced by the installation of a product referred to in an item in Part A is calculated by multiplying the abatement factor for that item by the regional factor applying to the place where the product is installed. Authorised by the Chief Parliamentary Counsel 121 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 26—Installation of high efficiency pool pump The following are the abatement factors and regional factors for each item in Part A: Item 26A Abatement factor: To be determined in accordance with the formula— 0·00674 × (1622 – PAEC) where PAEC is the projected annual energy consumption (kWh/y) listed on the energy rating label. 26A Regional factor: (a) If the product is installed in metropolitan Victoria: 0·98; (b) If the product is installed in regional Victoria: 1·04. Sch. 26 Pt C (Heading) Part C—Time at which activity substituted by S.R. No. undertaken and reduction in greenhouse 96/2013 reg. 8. gas emissions occurs Item 26A At the beginning of the day on which the installation of the product is completed. Authorised by the Chief Parliamentary Counsel 122 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 27—Data table Schedule 27—Data table Sch. 27 inserted by Regulation 4 S.R. No. 127/2010 reg. 13. Column 1 Column 2 Column 3 Column 4 Column 5 Regional/ Reticulated Item Postcode Metropolitan Gas Climatic Region 1 3000 Metropolitan Yes Metropolitan 2 3001 Metropolitan Yes Metropolitan 3 3002 Metropolitan Yes Metropolitan 4 3003 Metropolitan Yes Metropolitan 4A 3004 Metropolitan Yes Metropolitan 5 3005 Metropolitan Yes Metropolitan 6 3006 Metropolitan Yes Metropolitan 7 3008 Metropolitan Yes Metropolitan 8 3010 Metropolitan Yes Metropolitan 9 3011 Metropolitan Yes Metropolitan 10 3012 Metropolitan Yes Metropolitan 11 3013 Metropolitan Yes Metropolitan 12 3015 Metropolitan Yes Metropolitan 13 3016 Metropolitan Yes Metropolitan 14 3018 Metropolitan Yes Metropolitan 15 3019 Metropolitan Yes Metropolitan 16 3020 Metropolitan Yes Metropolitan 17 3021 Metropolitan Yes Metropolitan 18 3022 Metropolitan Yes Metropolitan 19 3023 Metropolitan Yes Metropolitan 20 3024 Metropolitan Yes Metropolitan 21 3025 Metropolitan Yes Metropolitan 22 3026 Metropolitan Yes Metropolitan 23 3027 Metropolitan Yes Metropolitan 24 3028 Metropolitan Yes Metropolitan 25 3029 Metropolitan Yes Metropolitan Authorised by the Chief Parliamentary Counsel 123 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 27—Data table Column 1 Column 2 Column 3 Column 4 Column 5 Regional/ Reticulated Item Postcode Metropolitan Gas Climatic Region 26 3030 Metropolitan Yes Metropolitan 27 3031 Metropolitan Yes Metropolitan 28 3032 Metropolitan Yes Metropolitan 29 3033 Metropolitan Yes Metropolitan 30 3034 Metropolitan Yes Metropolitan 31 3036 Metropolitan Yes Metropolitan 32 3037 Metropolitan Yes Metropolitan 33 3038 Metropolitan Yes Metropolitan 34 3039 Metropolitan Yes Metropolitan 35 3040 Metropolitan Yes Metropolitan 36 3041 Metropolitan Yes Metropolitan 37 3042 Metropolitan Yes Metropolitan 38 3043 Metropolitan Yes Metropolitan 39 3044 Metropolitan Yes Metropolitan 40 3045 Metropolitan Yes Metropolitan 41 3046 Metropolitan Yes Metropolitan 42 3047 Metropolitan Yes Metropolitan 43 3048 Metropolitan Yes Metropolitan 44 3049 Metropolitan Yes Metropolitan 45 3050 Metropolitan Yes Metropolitan 46 3051 Metropolitan Yes Metropolitan 47 3052 Metropolitan Yes Metropolitan 48 3053 Metropolitan Yes Metropolitan 49 3054 Metropolitan Yes Metropolitan 50 3055 Metropolitan Yes Metropolitan 51 3056 Metropolitan Yes Metropolitan 52 3057 Metropolitan Yes Metropolitan 53 3058 Metropolitan Yes Metropolitan Authorised by the Chief Parliamentary Counsel 124 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 27—Data table Column 1 Column 2 Column 3 Column 4 Column 5 Regional/ Reticulated Item Postcode Metropolitan Gas Climatic Region 54 3059 Metropolitan Yes Metropolitan 55 3060 Metropolitan Yes Metropolitan 56 3061 Metropolitan Yes Metropolitan 57 3062 Metropolitan Yes Metropolitan 58 3063 Metropolitan Yes Metropolitan 59 3064 Metropolitan Yes Metropolitan 60 3065 Metropolitan Yes Metropolitan 61 3066 Metropolitan Yes Metropolitan 62 3067 Metropolitan Yes Metropolitan 63 3068 Metropolitan Yes Metropolitan 64 3070 Metropolitan Yes Metropolitan 65 3071 Metropolitan Yes Metropolitan 66 3072 Metropolitan Yes Metropolitan 67 3073 Metropolitan Yes Metropolitan 68 3074 Metropolitan Yes Metropolitan 69 3075 Metropolitan Yes Metropolitan 70 3076 Metropolitan Yes Metropolitan 71 3078 Metropolitan Yes Metropolitan 72 3079 Metropolitan Yes Metropolitan 73 3081 Metropolitan Yes Metropolitan 74 3082 Metropolitan Yes Metropolitan 75 3083 Metropolitan Yes Metropolitan 76 3084 Metropolitan Yes Metropolitan 77 3085 Metropolitan Yes Metropolitan 78 3086 Metropolitan Yes Metropolitan 79 3087 Metropolitan Yes Metropolitan 80 3088 Metropolitan Yes Metropolitan 81 3089 Metropolitan Yes Metropolitan Authorised by the Chief Parliamentary Counsel 125 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 27—Data table Column 1 Column 2 Column 3 Column 4 Column 5 Regional/ Reticulated Item Postcode Metropolitan Gas Climatic Region 82 3090 Metropolitan Yes Metropolitan 83 3091 Metropolitan Yes Metropolitan 84 3093 Metropolitan Yes Metropolitan 85 3094 Metropolitan Yes Metropolitan 86 3095 Metropolitan Yes Metropolitan 87 3096 Metropolitan Yes Metropolitan 88 3097 Metropolitan Yes Metropolitan 89 3099 Metropolitan Yes Metropolitan 90 3101 Metropolitan Yes Metropolitan 91 3102 Metropolitan Yes Metropolitan 92 3103 Metropolitan Yes Metropolitan 93 3104 Metropolitan Yes Metropolitan 94 3105 Metropolitan Yes Metropolitan 95 3106 Metropolitan Yes Metropolitan 96 3107 Metropolitan Yes Metropolitan 97 3108 Metropolitan Yes Metropolitan 98 3109 Metropolitan Yes Metropolitan 99 3110 Metropolitan Yes Metropolitan 100 3111 Metropolitan Yes Metropolitan 101 3113 Metropolitan Yes Metropolitan 102 3114 Metropolitan Yes Metropolitan 103 3115 Metropolitan Yes Metropolitan 104 3116 Metropolitan Yes Metropolitan 105 3121 Metropolitan Yes Metropolitan 106 3122 Metropolitan Yes Metropolitan 107 3123 Metropolitan Yes Metropolitan 108 3124 Metropolitan Yes Metropolitan 109 3125 Metropolitan Yes Metropolitan Authorised by the Chief Parliamentary Counsel 126 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 27—Data table Column 1 Column 2 Column 3 Column 4 Column 5 Regional/ Reticulated Item Postcode Metropolitan Gas Climatic Region 110 3126 Metropolitan Yes Metropolitan 111 3127 Metropolitan Yes Metropolitan 112 3128 Metropolitan Yes Metropolitan 113 3129 Metropolitan Yes Metropolitan 114 3130 Metropolitan Yes Metropolitan 115 3131 Metropolitan Yes Metropolitan 116 3132 Metropolitan Yes Metropolitan 117 3133 Metropolitan Yes Metropolitan 118 3134 Metropolitan Yes Metropolitan 119 3135 Metropolitan Yes Metropolitan 120 3136 Metropolitan Yes Metropolitan 121 3137 Metropolitan Yes Metropolitan 122 3138 Metropolitan Yes Metropolitan 123 3139 Metropolitan Yes Metropolitan 124 3140 Metropolitan Yes Metropolitan 125 3141 Metropolitan Yes Metropolitan 126 3142 Metropolitan Yes Metropolitan 127 3143 Metropolitan Yes Metropolitan 128 3144 Metropolitan Yes Metropolitan 129 3145 Metropolitan Yes Metropolitan 130 3146 Metropolitan Yes Metropolitan 131 3147 Metropolitan Yes Metropolitan 132 3148 Metropolitan Yes Metropolitan 133 3149 Metropolitan Yes Metropolitan 134 3150 Metropolitan Yes Metropolitan 135 3151 Metropolitan Yes Metropolitan 136 3152 Metropolitan Yes Metropolitan 137 3153 Metropolitan Yes Metropolitan Authorised by the Chief Parliamentary Counsel 127 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 27—Data table Column 1 Column 2 Column 3 Column 4 Column 5 Regional/ Reticulated Item Postcode Metropolitan Gas Climatic Region 138 3154 Metropolitan Yes Metropolitan 139 3155 Metropolitan Yes Metropolitan 140 3156 Metropolitan Yes Metropolitan 141 3158 Metropolitan Yes Metropolitan 142 3159 Metropolitan Yes Metropolitan 143 3160 Metropolitan Yes Metropolitan 144 3161 Metropolitan Yes Metropolitan 145 3162 Metropolitan Yes Metropolitan 146 3163 Metropolitan Yes Metropolitan 147 3164 Metropolitan Yes Metropolitan 148 3165 Metropolitan Yes Metropolitan 149 3166 Metropolitan Yes Metropolitan 150 3167 Metropolitan Yes Metropolitan 151 3168 Metropolitan Yes Metropolitan 152 3169 Metropolitan Yes Metropolitan 153 3170 Metropolitan Yes Metropolitan 154 3171 Metropolitan Yes Metropolitan 155 3172 Metropolitan Yes Metropolitan 156 3173 Metropolitan Yes Metropolitan 157 3174 Metropolitan Yes Metropolitan 158 3175 Metropolitan Yes Metropolitan 159 3176 Metropolitan Yes Metropolitan 160 3177 Metropolitan Yes Metropolitan 161 3178 Metropolitan Yes Metropolitan 162 3179 Metropolitan Yes Metropolitan 163 3180 Metropolitan Yes Metropolitan 164 3181 Metropolitan Yes Metropolitan 165 3182 Metropolitan Yes Metropolitan Authorised by the Chief Parliamentary Counsel 128 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 27—Data table Column 1 Column 2 Column 3 Column 4 Column 5 Regional/ Reticulated Item Postcode Metropolitan Gas Climatic Region 166 3183 Metropolitan Yes Metropolitan 167 3184 Metropolitan Yes Metropolitan 168 3185 Metropolitan Yes Metropolitan 169 3186 Metropolitan Yes Metropolitan 170 3187 Metropolitan Yes Metropolitan 171 3188 Metropolitan Yes Metropolitan 172 3189 Metropolitan Yes Metropolitan 173 3190 Metropolitan Yes Metropolitan 174 3191 Metropolitan Yes Metropolitan 175 3192 Metropolitan Yes Metropolitan 176 3193 Metropolitan Yes Metropolitan 177 3194 Metropolitan Yes Metropolitan 178 3195 Metropolitan Yes Metropolitan 179 3196 Metropolitan Yes Metropolitan 180 3197 Metropolitan Yes Metropolitan 181 3198 Metropolitan Yes Metropolitan 182 3199 Metropolitan Yes Metropolitan 183 3200 Metropolitan Yes Metropolitan 184 3201 Metropolitan Yes Metropolitan 185 3202 Metropolitan Yes Metropolitan 186 3204 Metropolitan Yes Metropolitan 187 3205 Metropolitan Yes Metropolitan 188 3206 Metropolitan Yes Metropolitan 189 3207 Metropolitan Yes Metropolitan 190 3211 Regional Yes Mild 191 3212 Regional Yes Mild 192 3214 Regional Yes Mild 193 3215 Regional Yes Mild Authorised by the Chief Parliamentary Counsel 129 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 27—Data table Column 1 Column 2 Column 3 Column 4 Column 5 Regional/ Reticulated Item Postcode Metropolitan Gas Climatic Region 194 3216 Regional Yes Mild 195 3217 Regional Yes Mild 196 3218 Regional Yes Mild 197 3219 Regional Yes Mild 198 3220 Regional Yes Mild 199 3221 Regional Yes Mild 201 3222 Regional Yes Mild 202 3223 Regional Yes Mild 203 3224 Regional Yes Mild 204 3225 Regional Yes Mild 205 3226 Regional Yes Mild 206 3227 Regional Yes Mild 207 3228 Regional Yes Mild 208 3230 Regional Yes Mild 209 3231 Regional Yes Mild 210 3232 Regional No Mild 211 3233 Regional No Mild 212 3235 Regional No Mild 213 3236 Regional No Mild 214 3237 Regional No Mild 215 3238 Regional No Mild 216 3239 Regional No Mild 217 3240 Regional No Mild 218 3241 Regional No Mild 219 3242 Regional No Mild 220 3243 Regional No Mild 221 3249 Regional Yes Mild 222 3250 Regional Yes Mild Authorised by the Chief Parliamentary Counsel 130 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 27—Data table Column 1 Column 2 Column 3 Column 4 Column 5 Regional/ Reticulated Item Postcode Metropolitan Gas Climatic Region 223 3251 Regional Yes Mild 224 3254 Regional No Mild 225 3260 Regional Yes Mild 226 3264 Regional No Mild 227 3265 Regional Yes Mild 228 3266 Regional Yes Mild 229 3267 Regional No Mild 230 3268 Regional No Mild 231 3269 Regional No Mild 232 3270 Regional No Mild 233 3271 Regional No Mild 234 3272 Regional No Mild 235 3273 Regional No Mild 236 3274 Regional No Mild 237 3275 Regional No Mild 238 3276 Regional No Mild 239 3277 Regional Yes Mild 240 3278 Regional No Mild 241 3279 Regional No Mild 242 3280 Regional Yes Mild 243 3281 Regional No Mild 244 3282 Regional Yes Mild 245 3283 Regional No Mild 246 3284 Regional Yes Mild 247 3285 Regional No Mild 248 3286 Regional No Mild 249 3287 Regional No Mild 250 3289 Regional No Cold Authorised by the Chief Parliamentary Counsel 131 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 27—Data table Column 1 Column 2 Column 3 Column 4 Column 5 Regional/ Reticulated Item Postcode Metropolitan Gas Climatic Region 251 3292 Regional No Mild 252 3293 Regional No Cold 253 3294 Regional No Cold 254 3300 Regional Yes Cold 255 3301 Regional No Mild 256 3302 Regional No Mild 257 3303 Regional No Mild 258 3304 Regional No Mild 259 3305 Regional Yes Mild 260 3309 Regional No Mild 261 3310 Regional No Cold 262 3311 Regional No Cold 263 3312 Regional No Cold 264 3314 Regional No Cold 265 3315 Regional No Cold 266 3317 Regional No Cold 267 3318 Regional No Cold 268 3319 Regional No Cold 269 3321 Regional No Mild 270 3322 Regional No Mild 271 3323 Regional No Cold 272 3324 Regional No Cold 273 3325 Regional No Mild 274 3328 Regional No Mild 275 3329 Regional No Mild 276 3330 Regional No Cold 277 3331 Regional No Mild 278 3332 Regional No Mild Authorised by the Chief Parliamentary Counsel 132 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 27—Data table Column 1 Column 2 Column 3 Column 4 Column 5 Regional/ Reticulated Item Postcode Metropolitan Gas Climatic Region 279 3333 Regional No Mild 280 3334 Regional No Cold 281 3335 Metropolitan Yes Metropolitan 282 3337 Metropolitan Yes Metropolitan 283 3338 Metropolitan Yes Metropolitan 284 3340 Regional Yes Mild 285 3341 Regional No Cold 286 3342 Regional Yes Cold 287 3345 Regional No Cold 288 3350 Regional Yes Cold 289 3351 Regional No Cold 290 3352 Regional Yes Cold 291 3353 Regional No Cold 292 3354 Regional No Cold 293 3355 Regional Yes Cold 294 3356 Regional Yes Cold 295 3357 Regional Yes Cold 296 3360 Regional No Cold 297 3361 Regional No Cold 298 3363 Regional Yes Cold 299 3364 Regional Yes Cold 300 3370 Regional No Cold 301 3371 Regional No Cold 302 3373 Regional No Cold 302A 3374 Regional No Cold 303 3375 Regional No Cold 304 3377 Regional Yes Cold 305 3378 Regional No Cold Authorised by the Chief Parliamentary Counsel 133 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 27—Data table Column 1 Column 2 Column 3 Column 4 Column 5 Regional/ Reticulated Item Postcode Metropolitan Gas Climatic Region 306 3379 Regional No Cold 307 3380 Regional Yes Cold 308 3381 Regional No Cold 309 3384 Regional No Cold 310 3385 Regional No Cold 311 3387 Regional No Cold 312 3388 Regional No Cold 313 3390 Regional No Cold 314 3391 Regional No Cold 315 3392 Regional No Cold 316 3393 Regional No Cold 317 3395 Regional No Cold 318 3396 Regional No Cold 319 3400 Regional Yes Cold 320 3401 Regional Yes Cold 321 3402 Regional Yes Cold 322 3407 Regional No Cold 323 3409 Regional No Cold 324 3412 Regional No Cold 325 3413 Regional No Cold 326 3414 Regional No Cold 327 3415 Regional No Cold 328 3418 Regional No Cold 329 3419 Regional No Cold 330 3420 Regional No Cold 331 3423 Regional No Cold 332 3424 Regional No Cold 333 3427 Metropolitan Yes Metropolitan Authorised by the Chief Parliamentary Counsel 134 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 27—Data table Column 1 Column 2 Column 3 Column 4 Column 5 Regional/ Reticulated Item Postcode Metropolitan Gas Climatic Region 334 3428 Metropolitan Yes Metropolitan 335 3429 Metropolitan Yes Metropolitan 336 3430 Regional No Mild 337 3431 Regional Yes Cold 338 3432 Regional No Cold 338A 3433 Regional No Cold 339 3434 Regional Yes Cold 340 3435 Regional Yes Cold 341 3437 Regional Yes Cold 342 3438 Regional Yes Cold 343 3440 Regional Yes Cold 344 3441 Regional Yes Cold 345 3442 Regional Yes Cold 346 3444 Regional Yes Cold 347 3446 Regional No Cold 348 3447 Regional No Cold 349 3448 Regional No Cold 350 3450 Regional Yes Cold 351 3451 Regional Yes Cold 352 3453 Regional No Cold 353 3458 Regional No Cold 354 3460 Regional Yes Cold 355 3461 Regional Yes Cold 356 3462 Regional No Cold 357 3463 Regional No Cold 358 3464 Regional Yes Cold 359 3465 Regional Yes Cold 360 3467 Regional No Cold Authorised by the Chief Parliamentary Counsel 135 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 27—Data table Column 1 Column 2 Column 3 Column 4 Column 5 Regional/ Reticulated Item Postcode Metropolitan Gas Climatic Region 361 3468 Regional No Cold 362 3469 Regional No Cold 363 3472 Regional No Cold 364 3475 Regional No Cold 364A 3477 Regional No Cold 365 3478 Regional No Cold 366 3480 Regional No Cold 367 3482 Regional No Cold 368 3483 Regional No Cold 369 3485 Regional No Cold 370 3487 Regional No Hot 371 3488 Regional No Hot 372 3489 Regional No Hot 373 3490 Regional No Hot 374 3491 Regional No Hot 375 3494 Regional Yes Hot 376 3496 Regional Yes Hot 377 3498 Regional Yes Hot 378 3500 Regional Yes Hot 379 3501 Regional Yes Hot 380 3502 Regional Yes Hot 381 3505 Regional Yes Hot 382 3506 Regional No Hot 383 3507 Regional No Hot 384 3509 Regional No Hot 385 3512 Regional No Hot 386 3515 Regional No Cold 387 3516 Regional No Cold Authorised by the Chief Parliamentary Counsel 136 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 27—Data table Column 1 Column 2 Column 3 Column 4 Column 5 Regional/ Reticulated Item Postcode Metropolitan Gas Climatic Region 388 3517 Regional No Cold 389 3518 Regional No Cold 390 3520 Regional No Cold 391 3521 Regional No Cold 392 3522 Regional No Cold 393 3523 Regional No Cold 394 3525 Regional No Cold 395 3527 Regional No Cold 396 3529 Regional No Hot 397 3530 Regional No Hot 398 3531 Regional No Hot 399 3533 Regional No Hot 400 3537 Regional No Hot 401 3540 Regional No Hot 402 3542 Regional No Hot 403 3544 Regional No Hot 404 3546 Regional No Hot 405 3549 Regional No Hot 406 3550 Regional Yes Cold 407 3551 Regional Yes Cold 408 3552 Regional No Cold 409 3554 Regional No Cold 410 3555 Regional Yes Cold 411 3556 Regional Yes Cold 412 3557 Regional No Cold 413 3558 Regional No Cold 414 3559 Regional No Cold 415 3561 Regional Yes Cold Authorised by the Chief Parliamentary Counsel 137 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 27—Data table Column 1 Column 2 Column 3 Column 4 Column 5 Regional/ Reticulated Item Postcode Metropolitan Gas Climatic Region 416 3562 Regional No Cold 417 3563 Regional Yes Cold 418 3564 Regional Yes Cold 419 3565 Regional No Cold 420 3566 Regional Yes Hot 421 3567 Regional No Hot 422 3568 Regional No Hot 423 3570 Regional No Cold 424 3571 Regional No Cold 425 3572 Regional No Cold 426 3573 Regional No Cold 427 3575 Regional No Hot 428 3576 Regional No Hot 429 3579 Regional No Hot 430 3580 Regional No Hot 431 3581 Regional No Hot 432 3583 Regional No Hot 433 3584 Regional No Hot 434 3585 Regional No Hot 434A 3586 Regional No Hot 435 3588 Regional No Hot 436 3589 Regional No Hot 437 3590 Regional No Hot 438 3591 Regional No Hot 439 3594 Regional No Hot 440 3595 Regional No Hot 441 3596 Regional No Hot 442 3597 Regional No Hot Authorised by the Chief Parliamentary Counsel 138 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 27—Data table Column 1 Column 2 Column 3 Column 4 Column 5 Regional/ Reticulated Item Postcode Metropolitan Gas Climatic Region 443 3599 Regional No Hot 444 3607 Regional No Cold 445 3608 Regional No Cold 446 3610 Regional Yes Cold 447 3612 Regional No Cold 448 3614 Regional No Cold 449 3616 Regional Yes Cold 450 3617 Regional No Cold 451 3618 Regional Yes Cold 452 3619 Regional No Cold 453 3620 Regional Yes Cold 454 3621 Regional Yes Cold 455 3622 Regional No Cold 456 3623 Regional Yes Cold 457 3624 Regional Yes Cold 458 3629 Regional Yes Cold 459 3630 Regional Yes Cold 460 3631 Regional Yes Cold 461 3632 Regional No Cold 462 3633 Regional No Cold 463 3634 Regional No Cold 464 3635 Regional No Cold 465 3636 Regional Yes Cold 466 3637 Regional No Cold 467 3638 Regional No Cold 468 3639 Regional No Cold 469 3640 Regional Yes Cold 470 3641 Regional Yes Cold Authorised by the Chief Parliamentary Counsel 139 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 27—Data table Column 1 Column 2 Column 3 Column 4 Column 5 Regional/ Reticulated Item Postcode Metropolitan Gas Climatic Region 471 3643 Regional Yes Cold 472 3644 Regional Yes Cold 473 3646 Regional No Cold 474 3647 Regional No Cold 475 3649 Regional No Cold 476 3658 Regional Yes Cold 477 3659 Regional Yes Cold 478 3660 Regional Yes Cold 479 3661 Regional No Cold 480 3662 Regional No Cold 481 3663 Regional No Cold 482 3664 Regional No Cold 483 3665 Regional No Cold 484 3666 Regional Yes Cold 485 3669 Regional No Cold 486 3670 Regional No Cold 487 3671 Regional No Cold 488 3672 Regional Yes Cold 489 3673 Regional No Cold 490 3675 Regional No Cold 491 3676 Regional No Cold 492 3677 Regional Yes Cold 493 3678 Regional Yes Cold 494 3682 Regional No Cold 495 3683 Regional Yes Cold 496 3685 Regional Yes Cold 497 3687 Regional Yes Cold 498 3688 Regional No Cold Authorised by the Chief Parliamentary Counsel 140 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 27—Data table Column 1 Column 2 Column 3 Column 4 Column 5 Regional/ Reticulated Item Postcode Metropolitan Gas Climatic Region 499 3689 Regional No Cold 500 3690 Regional Yes Cold 501 3691 Regional Yes Cold 502 3694 Regional Yes Cold 503 3695 Regional No Cold 504 3697 Regional No Cold 505 3698 Regional No Cold 506 3699 Regional No Cold 507 3700 Regional No Cold 508 3701 Regional No Cold 509 3704 Regional No Cold 510 3705 Regional No Cold 511 3707 Regional No Cold 512 3708 Regional No Cold 513 3709 Regional No Cold 514 3711 Regional No Cold 515 3712 Regional No Cold 516 3713 Regional No Cold 517 3714 Regional No Cold 518 3715 Regional No Cold 519 3717 Regional No Cold 520 3718 Regional No Cold 521 3719 Regional No Cold 522 3720 Regional No Cold 523 3722 Regional No Cold 524 3723 Regional No Cold 525 3724 Regional No Cold 526 3725 Regional No Cold Authorised by the Chief Parliamentary Counsel 141 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 27—Data table Column 1 Column 2 Column 3 Column 4 Column 5 Regional/ Reticulated Item Postcode Metropolitan Gas Climatic Region 527 3726 Regional No Cold 528 3727 Regional No Cold 529 3728 Regional No Cold 530 3730 Regional Yes Cold 531 3732 Regional No Cold 532 3733 Regional No Cold 533 3735 Regional No Cold 534 3736 Regional No Cold 535 3737 Regional No Cold 536 3738 Regional No Cold 537 3739 Regional No Cold 538 3740 Regional No Cold 539 3741 Regional No Cold 540 3744 Regional No Cold 541 3746 Regional No Cold 542 3747 Regional No Cold 543 3749 Regional No Cold 544 3750 Regional Yes Mild 545 3751 Regional Yes Mild 546 3752 Regional Yes Mild 547 3753 Regional Yes Mild 548 3754 Regional Yes Mild 549 3755 Regional Yes Mild 550 3756 Regional Yes Mild 551 3757 Regional Yes Mild 552 3758 Regional No Mild 553 3759 Regional Yes Mild 554 3760 Regional Yes Mild Authorised by the Chief Parliamentary Counsel 142 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 27—Data table Column 1 Column 2 Column 3 Column 4 Column 5 Regional/ Reticulated Item Postcode Metropolitan Gas Climatic Region 555 3761 Regional Yes Mild 556 3762 Regional No Cold 557 3763 Regional Yes Cold 558 3764 Regional Yes Cold 559 3765 Metropolitan Yes Metropolitan 560 3766 Regional Yes Cold 561 3767 Regional Yes Cold 562 3770 Regional Yes Cold 563 3775 Regional Yes Cold 564 3777 Regional Yes Cold 565 3778 Regional No Cold 566 3779 Regional No Cold 567 3781 Metropolitan Yes Metropolitan 568 3782 Metropolitan Yes Metropolitan 569 3783 Metropolitan Yes Metropolitan 569A 3785 Regional Yes Cold 570 3786 Regional Yes Cold 571 3787 Regional Yes Cold 572 3788 Regional Yes Cold 573 3789 Regional Yes Cold 574 3791 Metropolitan Yes Metropolitan 575 3792 Regional Yes Cold 576 3793 Regional Yes Cold 577 3795 Regional Yes Cold 578 3796 Regional Yes Cold 579 3797 Regional Yes Mild 580 3799 Regional Yes Cold 581 3800 Regional Yes Mild Authorised by the Chief Parliamentary Counsel 143 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 27—Data table Column 1 Column 2 Column 3 Column 4 Column 5 Regional/ Reticulated Item Postcode Metropolitan Gas Climatic Region 582 3802 Metropolitan Yes Metropolitan 583 3803 Metropolitan Yes Metropolitan 584 3804 Metropolitan Yes Metropolitan 585 3805 Metropolitan Yes Metropolitan 586 3806 Metropolitan Yes Metropolitan 587 3807 Metropolitan Yes Metropolitan 588 3808 Metropolitan Yes Metropolitan 589 3809 Metropolitan Yes Metropolitan 590 3810 Metropolitan Yes Metropolitan 591 3812 Regional Yes Mild 592 3813 Regional Yes Mild 593 3814 Regional Yes Mild 594 3815 Regional Yes Mild 595 3816 Regional Yes Mild 596 3818 Regional Yes Mild 597 3820 Regional Yes Mild 598 3821 Regional No Mild 599 3822 Regional Yes Mild 600 3823 Regional Yes Mild 601 3824 Regional Yes Mild 602 3825 Regional Yes Mild 603 3831 Regional No Mild 604 3832 Regional No Mild 605 3833 Regional No Cold 606 3835 Regional No Mild 607 3840 Regional Yes Mild 608 3841 Regional No Mild 609 3842 Regional Yes Mild Authorised by the Chief Parliamentary Counsel 144 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 27—Data table Column 1 Column 2 Column 3 Column 4 Column 5 Regional/ Reticulated Item Postcode Metropolitan Gas Climatic Region 610 3844 Regional Yes Mild 611 3847 Regional Yes Mild 612 3850 Regional Yes Mild 613 3851 Regional Yes Mild 614 3852 Regional Yes Mild 615 3853 Regional Yes Mild 616 3854 Regional No Mild 617 3856 Regional No Mild 618 3857 Regional No Mild 619 3858 Regional No Mild 620 3859 Regional No Mild 621 3860 Regional Yes Cold 622 3862 Regional No Cold 623 3864 Regional No Cold 624 3865 Regional No Mild 625 3869 Regional No Mild 626 3870 Regional No Mild 627 3871 Regional No Mild 628 3873 Regional No Mild 629 3874 Regional No Mild 630 3875 Regional Yes Mild 631 3878 Regional Yes Mild 632 3880 Regional Yes Mild 633 3882 Regional No Mild 634 3885 Regional No Mild 635 3886 Regional No Mild 636 3887 Regional No Mild 637 3888 Regional No Mild Authorised by the Chief Parliamentary Counsel 145 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 27—Data table Column 1 Column 2 Column 3 Column 4 Column 5 Regional/ Reticulated Item Postcode Metropolitan Gas Climatic Region 638 3889 Regional No Cold 639 3890 Regional No Mild 640 3891 Regional No Mild 641 3892 Regional No Mild 642 3893 Regional No Cold 643 3895 Regional No Cold 644 3896 Regional No Cold 645 3898 Regional No Cold 646 3900 Regional No Cold 647 3902 Regional No Mild 648 3903 Regional No Mild 649 3904 Regional No Mild 650 3909 Regional No Mild 651 3910 Metropolitan Yes Metropolitan 652 3911 Metropolitan Yes Metropolitan 653 3912 Metropolitan Yes Metropolitan 654 3913 Metropolitan Yes Metropolitan 655 3915 Metropolitan Yes Metropolitan 656 3916 Metropolitan Yes Metropolitan 657 3918 Metropolitan Yes Metropolitan 658 3919 Metropolitan Yes Metropolitan 659 3920 Metropolitan Yes Metropolitan 660 3921 Regional Yes Mild 661 3922 Regional No Mild 662 3923 Regional No Mild 663 3925 Regional No Mild 664 3926 Regional Yes Mild 665 3927 Regional Yes Mild Authorised by the Chief Parliamentary Counsel 146 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 27—Data table Column 1 Column 2 Column 3 Column 4 Column 5 Regional/ Reticulated Item Postcode Metropolitan Gas Climatic Region 666 3928 Regional Yes Mild 667 3929 Regional Yes Mild 668 3930 Regional Yes Mild 669 3931 Regional Yes Mild 670 3933 Regional Yes Mild 671 3934 Regional Yes Mild 672 3936 Regional Yes Mild 673 3937 Regional Yes Mild 674 3938 Regional Yes Mild 675 3939 Regional Yes Mild 676 3940 Regional Yes Mild 677 3941 Regional Yes Mild 678 3942 Regional Yes Mild 679 3943 Regional Yes Mild 680 3944 Regional Yes Mild 681 3945 Regional No Mild 682 3946 Regional No Cold 683 3950 Regional Yes Mild 684 3951 Regional No Mild 685 3953 Regional Yes Mild 686 3954 Regional No Mild 687 3956 Regional No Mild 688 3957 Regional No Mild 689 3958 Regional No Cold 690 3959 Regional No Mild 691 3960 Regional No Mild 692 3962 Regional No Mild 693 3964 Regional No Cold Authorised by the Chief Parliamentary Counsel 147 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008

Schedule 27—Data table Column 1 Column 2 Column 3 Column 4 Column 5 Regional/ Reticulated Item Postcode Metropolitan Gas Climatic Region 694 3965 Regional No Mild 695 3966 Regional No Cold 696 3967 Regional No Cold 697 3971 Regional No Cold 698 3975 Metropolitan Yes Metropolitan 699 3976 Metropolitan Yes Metropolitan 700 3977 Metropolitan Yes Metropolitan 701 3978 Regional Yes Mild 702 3979 Regional No Mild 703 3980 Regional Yes Cold 704 3981 Regional Yes Cold 705 3984 Regional Yes Mild 706 3987 Regional Yes Mild 707 3988 Regional No Cold 708 3990 Regional No Mild 709 3991 Regional No Mild 710 3992 Regional No Mild 711 3995 Regional Yes Mild 712 3996 Regional Yes Mild Authorised by the Chief Parliamentary Counsel 148 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 28—Replacement of gas heating ductwork Schedule 28—Replacement of gas Sch. 28 inserted by heating ductwork S.R. No. 56/2011 reg. 6, Regulation 6(1)(w) amended by S.R. No. Prescribed activity under regulation 6(1)(w): decommissioning gas heating 6/2012 reg. 33. ductwork that is connected to a ducted gas heater and installing in its place a product that complies with the criteria specified in Part A of Schedule 28. Part A—Criteria Item 28A Ductwork that— (a) is tested and certified by an approved laboratory as complying with AS 4254–2002; and (b) is insulated using bulk insulation that is certified by an accredited body or approved laboratory as complying with AS/NZS 4859.1:2002 and achieves a minimum R-value of R1.5 when measured in accordance with AS/NZS 4859.1:2002; and (c) is longitudinally labelled at intervals of not more than 1·5 meters, in characters that are clearly legible and at least 18mm high stating— (i) the duct manufacturer's or duct assembler's name; and (ii) the diameter of the duct core; and (iii) the R-value of the bulk insulation; and (iv) whether the ductwork complies with AS 4254–2002; and (d) is installed and supported in accordance with the requirements set out in AS 4254–2002; and (e) uses fittings that achieve at least the R-value specified by Table 3.12.5.2 of the Building Code. Authorised by the Chief Parliamentary Counsel 149 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 28—Replacement of gas heating ductwork Sch. 28 Pt B amended by Part B—Calculation of carbon dioxide S.R. No. 32/2012 equivalents of greenhouse gases reg. 35. The carbon dioxide equivalent (in tonnes) of greenhouse gases to be reduced by the decommissioning of existing gas heating ductwork and the installation of ductwork referred to in an item in Part A is calculated by multiplying the abatement factor for that item by the regional factor applying to the place where the ductwork is installed. The following are the abatement factors and regional factors for each item in Part A: Item 28A Abatement factor: (a) if the ductwork is connected to a heater that has a rated output heating capacity of not less than 10 and not more than 18kW: 12·13; (b) if the ductwork is connected to a heater that has a rated output heating capacity of more than 18 and not more than 28kW: 15·40; (c) if the ductwork is connected to a heater that has a rated output heating capacity of more than 28kW: 18·86; (d) if the ductwork is installed but the output heating capacity of the heater is not known: 12·13. 28A Regional factor: (a) If the product is installed in metropolitan Victoria: 1·00; (b) If the product is installed in regional Victoria—climatic region Mild: 1·00; (c) If the product is installed in regional Victoria—climatic region Cold: 1·61; (d) If the product is installed in regional Victoria—climatic region Hot: 0·71. Authorised by the Chief Parliamentary Counsel 150 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 28—Replacement of gas heating ductwork Part C—Time at which activity Sch. 28 Pt C (Heading) undertaken and reduction in greenhouse substituted by S.R. No. gas emissions occurs 96/2013 reg. 8. Item 28A At the beginning of whichever of the following days is later— (a) the day on which the installation of the product is completed; or (b) the day on which a ducted gas heater connected to the product is first able to produce and deliver ducted gas heating. Authorised by the Chief Parliamentary Counsel 151 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 29—Installation of standby power controller Sch. 29 inserted by Schedule 29—Installation of standby S.R. No. 56/2011 reg. 6, power controller amended by Regulation 6(1)(x) S.R. No. 6/2012 Prescribed activity under regulation 6(1)(x): Installing a standby power reg. 34(a)(b). controller, being a product that complies with the criteria specified in Part A of Schedule 29. Part A—Criteria Item Sch. 29 29A A product that when installed in an information item 29A amended by technology environment is able to automatically reduce S.R. No. the standby energy consumption of information 6/2012 reg. 34(c). technology equipment connected to it, and— (a) when tested by an approved laboratory in accordance with a laboratory test approved by the ESC, is determined to be suitable for use in an information technology environment and, in particular, is demonstrated to— (i) be suitable for use with desktop and notebook computers that are not more than 2 years old; and (ii) be capable of controlling the power of at least 4 appliances (whether directly or indirectly); and (iii) be fitted with a mains power switching device that is rated to a minimum of 50 000 switching cycles; and (iv) have an electric power consumption of not more than 1 watt when tested in accordance with the laboratory test; and (v) automatically disconnect mains power from controlled appliances when the master computer is switched to Off Mode; and Authorised by the Chief Parliamentary Counsel 152 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 29—Installation of standby power controller (vi) automatically reconnect mains power to the controlled appliances when the master computer enters Active State; and (vii) not be reliant on a universal serial bus connection to determine the operating mode of the computer; and (viii) be able, at the time of installation, to disconnect mains power from or reconnect mains power to controlled appliances without having to be set up to have those functions assigned to the operation of an existing appliance remote control; and (ix) not require manual setting of a current or power threshold; and (b) is connected to at least 2 controlled appliances at the time of installation. 29B A product that when installed in an audio visual environment is able to automatically reduce the standby energy consumption of home audio visual equipment connected to it, and— (a) when tested by an approved laboratory in accordance with a laboratory test approved by the ESC, is determined to be suitable for use in an audio visual environment and, in particular, is demonstrated to— (i) be capable of controlling the power of at least 4 appliances (whether directly or indirectly); and (ii) be fitted with a mains power switching device that is rated to a minimum of 50 000 switching cycles; and (iii) have an electric power consumption of not more than 1 watt when tested in accordance with the laboratory test; and Authorised by the Chief Parliamentary Counsel 153 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 29—Installation of standby power controller (iv) automatically disconnect mains power from controlled appliances— (A) in the case of a product that relies on a master/slave arrangement—when the master appliance is turned off; (B) in the case of a product that relies on sensing infra-red signals from the remote controls of controlled appliances—after a period of time specified in the laboratory test when the product does not detect infra-red signals from those remote controls that are triggered by a user; and (v) automatically reconnect mains power to the controlled appliances only when— (A) in the case of a product that relies on a master/slave arrangement—when the master appliance is turned on; (B) in the case of a product that relies on sensing infra-red signals from the remote controls of controlled appliances—when any of the controlled appliances are operated by a user; and (vi) be able, at the time of installation, to disconnect mains power from or reconnect mains power to controlled appliances without having to be set up to have those functions assigned to the operation of an existing appliance remote control; and (vii) not require manual setting of a current or power threshold; and (b) is connected to at least 2 controlled appliances at the time of installation. Authorised by the Chief Parliamentary Counsel 154 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 29—Installation of standby power controller Part B—Calculation of carbon dioxide Sch. 29 Pt B substituted by equivalents of greenhouse gases S.R. No. 146/2011 The carbon dioxide equivalent (in tonnes) of greenhouse reg. 25, amended by gases to be reduced by the installation of a product or S.R. Nos products referred to in an item in Part A is the sum of the 6/2012 reg. 34(d), figures obtained by multiplying the number of products 32/2012 installed (not being more than 4 if in residential premises) reg. 36. in the premises under each item in Part A, by the abatement factor for that item. The following are the abatement factors and regional factors for each item in Part A: Item 29A Abatement Factor: Sch. 29 item 29A substituted by (a) A product that is installed in residential premises S.R. No. and— 6/2012 reg. 34(e). (i) satisfies the minimum eligibility criteria for an item 29A in Part A: 1·0; (ii) satisfies the minimum eligibility criteria for an item 29A in Part A and is capable of automatically disconnecting mains power to controlled appliances when the master computer enters Sleep Mode, and has been demonstrated, to the satisfaction of the ESC, to be capable of achieving abatement of greater than or equal to 1·5 tonnes over a 10 year period and has been subjected to a field trial approved by the ESC: At where At is the tonnes of abatement, not exceeding 6·0, that the product has demonstrated to be capable of achieving to the satisfaction of the ESC. Authorised by the Chief Parliamentary Counsel 155 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 29—Installation of standby power controller (b) A product that is installed in business or other non- residential premises and— (i) satisfies the minimum eligibility criteria for an item 29A in Part A: 0·43; (ii) satisfies the minimum eligibility criteria for an item 29A in Part A and is connected to at least 3 controlled appliances at the time of installation: 0·61; (iii) satisfies the minimum eligibility criteria for an item 29A in Part A and is capable of automatically disconnecting mains power to controlled appliances when the master computer enters Sleep Mode, and has been demonstrated, to the satisfaction of the ESC, to be capable of achieving abatement of greater than or equal to 1·5 tonnes over a 10 year period and has been subjected to a field trial approved by the ESC: At where At is the tonnes of abatement, not exceeding 6·0, that the product has demonstrated to be capable of achieving to the satisfaction of the ESC. Sch. 29 29B Abatement Factor: item 29B substituted by S.R. No. (a) A product that is installed in residential premises 6/2012 and— reg. 34(e). (i) satisfies the minimum eligibility criteria for item 29B in Part A: 1·0 (ii) A product that satisfies the minimum eligibility criteria for item 29B in Part A and does not operate solely on the basis of a master/slave arrangement, and has been demonstrated, to the satisfaction of the ESC, to be capable of achieving Authorised by the Chief Parliamentary Counsel 156 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008

Schedule 29—Installation of standby power controller abatement of greater than or equal to 1·5 tonnes over a 10 year period and has been subjected to a field trial approved by the ESC: At where At is the tonnes of abatement, not exceeding 6·0, that the product has demonstrated to be capable of achieving to the satisfaction of the ESC. (b) A product that is installed in business or other non-residential premises and— (i) satisfies the minimum eligibility criteria for an item 29B in Part A: 0·45; (ii) satisfies the minimum eligibility criteria for an item 29B in Part A and is connected to at least 3 controlled appliances at the time of installation: 0·65. Sch. 29 Pt C Part C—Time at which activity (Heading) substituted by undertaken and reduction in greenhouse S.R. No. 96/2013 reg. 8. gas emissions occurs Item 29A–29B At the beginning of the day on which the installation of the product or products is completed. Authorised by the Chief Parliamentary Counsel 157 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 30—In-home display unit Sch. 30 inserted by Schedule 30—In-home display unit S.R. No. Regulation 6(2)(c) 14/2012 reg. 7. Prescribed activity under regulation 6(2)(c): Installing an in-home display unit that complies with the criteria specified in Part A of Schedule 30. Part A—Criteria Item 30A A product that when installed in relation to an AMI metering installation provides information on the total electricity consumption of the residential premises directly to the consumer in respect of whom the installation is undertaken, and— (a) complies with the ZigBee Smart Energy Profile Specification published by the ZigBee Standards Organisation on 1 December 2008 and the ZigBee Smart Energy Profile Specification version 1.1 published by the ZigBee Standards Organisation on 23 March 2011; and (b) when tested by an approved laboratory in accordance with a laboratory test approved by the ESC, is demonstrated to— (i) determine electricity consumption information from the sensing apparatus at least every 30 seconds; and (ii) be able to store electricity energy consumption information from the previous 45 days; and (iii) be able to display to the consumer (or relay to a device that is capable of displaying to the consumer) in a numerical format and a format other than a numerical format that allows the consumer to easily distinguish between low and high consumption— Authorised by the Chief Parliamentary Counsel 158 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 30—In-home display unit (A) electricity energy consumption information from the previous 45 days in intervals no longer than one hour per day of information displayed and one day per week of information displayed; and (B) the average total household electrical power consumption (in watts) for the displayed period, which must be updated at least every 30 seconds; and (C) the total household electricity energy consumption (in kWh) for the displayed period and the cost of that consumption, which must be updated at least every 30 seconds; and (iv) be able to display to the consumer (or relay to a device that is capable of displaying to the consumer) the tariff (in cost per unit of energy consumed) and the total cost of electricity consumed for the period displayed; and (v) be able to permanently erase all consumption and tariff information held by the product including all information entered by the consumer; and (vi) have an average electric power consumption of not more than 0·6 watts when operating under normal circumstances; and (c) if battery powered, uses a battery that has a manufacturer's rated lifetime of at least 5 years when operating under normal circumstances. 30B A product that when installed in relation to any sensing apparatus provides information on the total electricity consumption of the residential premises directly to the consumer in respect of whom the installation is undertaken, and— Authorised by the Chief Parliamentary Counsel 159 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 30—In-home display unit (a) when tested by an approved laboratory in accordance with a laboratory test approved by the ESC, is demonstrated to— (i) determine electricity consumption information from the sensing apparatus at least every 30 seconds; and (ii) be able to store electricity energy consumption information from the previous 45 days; and (iii) be able to display to the consumer (or relay to a device that is capable of displaying to the consumer) in a numerical format and a format other than a numerical format that allows the consumer to easily distinguish between low and high consumption— (A) electricity energy consumption information from the previous 45 days in intervals no longer than one hour per day of information displayed and one day per week of information displayed; and (B) the average total household electrical power consumption (in watts) for the displayed period, which must be updated at least every 30 seconds; and (C) the total household electricity energy consumption (in kWh) for the displayed period and the cost of that consumption, which must be updated at least every 30 seconds; and (iv) be able to display to the consumer (or relay to a device that is capable of displaying to the consumer) the tariff (in cost per unit of energy consumed) and the total cost of electricity consumed for the period displayed; and Authorised by the Chief Parliamentary Counsel 160 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 30—In-home display unit (v) be able to permanently erase all consumption and tariff information held by the product (including all information entered by the consumer); and (vi) have an average electric power consumption of not more than 0·6 watts when operating under normal circumstances; and (vii) is demonstrated to provide electricity energy consumption information that is accurate to within 5% of actual electricity consumption; and (b) if battery powered, uses a battery that has a manufacturer's rated lifetime of at least 5 years when operating under normal circumstances; and (c) uses, for its communications with the sensing apparatus and any display device, an encrypted communication protocol that is approved by the ESC. Sch. 30 Pt B Part B—Calculation of carbon dioxide amended by S.R. No. equivalents of greenhouse gases 32/2012 reg. 37. The carbon dioxide equivalent (in tonnes) of greenhouse gases to be reduced by the installation of a product referred to in an item in Part A is calculated by multiplying the abatement factor for that item by the regional factor applying to the place where the product is installed. The following are the abatement factors and regional factors for each item in Part A: Item 30A–30B Abatement factor: (a) If the product is installed in a non-gas reticulated area: 2·47; (b) If the product is installed in a gas reticulated area: 1·87. Authorised by the Chief Parliamentary Counsel 161 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 30—In-home display unit 30A–30B Regional factor: (a) If the product is installed in metropolitan Victoria: 0·98; (b) If the product is installed in regional Victoria: 1·04. Sch. 30 Pt C (Heading) Part C—Time at which activity substituted by S.R. No. undertaken and reduction in greenhouse 96/2013 reg. 8. gas emissions occurs Item 30A–30B At the beginning of the first day on which the product is connected to the sensing apparatus and provides total household electricity consumption information to the consumer. Authorised by the Chief Parliamentary Counsel 162 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 31—High efficiency motor Schedule 31—High efficiency motor Sch. 31 (Heading) Regulation 6(3)(a) amended by S.R. No. Prescribed activity under regulation 6(3)(a): Installing a three-phase 167/2015 induction motor that complies with the criteria specified in Part A of reg. 13(1)(a). Schedule 31. Sch. 31 inserted by S.R. No. Part A—Criteria 32/2012 reg. 38, Item amended by S.R. No. 167/2015 reg. 13(1)(b). 31A A three-phase cage induction motor that— Sch. 31 Pt A item 31A substituted by (a) has a rated output, as determined in accordance with S.R. No. AS 60034.1-2009, of not less than 0∙75 and not more 167/2015 reg. 13(2). than 185 kW; and (b) is labelled or marked as a high efficiency motor; and (c) does not meet the requirements for an IE4 (super-premium) efficiency level motor proposed in Appendix A of IEC/TS 60034-31 when tested in accordance with IEC 60034-2-1; and (d) has 2, 4, 6 or 8 poles; and (e) is listed on the ESC register. 31B A three-phase cage induction motor that— Sch. 31 Pt A item 31B substituted by (a) has a rated output, as determined in accordance with S.R. No. AS 60034.1-2009, of not less than 0∙75 and not more 167/2015 reg. 13(3). than 185 kW; and (b) meets the requirements for an IE4 (super-premium) efficiency level motor proposed in Appendix A of IEC/TS 60034-31 when tested in accordance with IEC 60034-2-1; and (c) has 2, 4 or 6 poles; and (d) is listed on the ESC register. Authorised by the Chief Parliamentary Counsel 163 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 31—High efficiency motor Sch. 31 Pt B amended by Part B—Calculation of carbon dioxide S.R. No. 167/2015 equivalents of greenhouse gases reg. 13(4). The carbon dioxide equivalent (in tonnes) of greenhouse gases to be reduced by the installation of a product referred to in an item in Part A is calculated by multiplying the abatement factor for that item (determined according to the minimum rated output of the motor) by the regional factor applying to the place where the product is installed. The following are the abatement factors and regional factors for each item in Part A: Item 31A The abatement factor for a motor is specified in column 3 of the following Table in respect of the minimum rated output (in kW) of the motor, as specified in column 2 of that Table. Sch. 31 Pt B Column 1 Column 2 Column 3 item 31A Abatement factor (Table) Item Minimum rated output (kW) amended by 1 0·75 0∙28 S.R. No. 167/2015 2 1·1 0∙38 reg. 13(5). 3 1·5 0∙45 4 2·2 0∙61 5 3 1∙03 6 4 1∙27 7 5·5 1∙60 8 7·5 1∙99 9 11 3∙74 10 15 4∙64 11 18·5 5∙42 12 22 6∙12 13 30 7∙75 14 37 8∙71 15 45 13∙33 Authorised by the Chief Parliamentary Counsel 164 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 31—High efficiency motor Column 1 Column 2 Column 3 Abatement factor Item Minimum rated output (kW) 16 55 15∙16 17 75 19∙51 18 90 20∙55 19 110 32∙71 20 132 34∙92 21 150 38∙33 22 185 47∙28 31B The abatement factor for a motor is specified in column 3 of the following Table in respect of the minimum rated output (in kW) of the motor, as specified in column 2 of that Table. Column 1 Column 2 Column 3 Sch. 31 Pt B Abatement factor item 31B Item Minimum rated output (kW) (Table) 1 0·75 0∙55 amended by S.R. No. 2 1·1 0∙76 167/2015 reg. 13(6). 3 1·5 0∙88 4 2·2 1∙25 5 3 2∙08 6 4 2∙46 7 5·5 3∙50 8 7·5 4∙17 9 11 8∙56 10 15 10∙02 11 18·5 11∙72 12 22 13∙77 13 30 15∙83 14 37 17∙94 15 45 27∙47 16 55 31∙69 Authorised by the Chief Parliamentary Counsel 165 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008

Schedule 31—High efficiency motor Column 1 Column 2 Column 3 Item Minimum rated output (kW) Abatement factor 17 75 34∙89 18 90 38∙09 19 110 55∙51 20 132 58∙09 21 150 57∙59 22 185 78∙20 31A–31B Regional factor: (a) If the product is installed in metropolitan Victoria: 0·98; (b) If the product is installed in regional Victoria: 1·04. Sch. 31 Pt C (Heading) Part C—Time at which activity substituted by S.R. No. undertaken and reduction in greenhouse 96/2013 reg. 8. gas emissions occurs Item Sch. 31 Pt C 31A–31B At the beginning of the day on which the installed item 31A–31B substituted by product is first able to deliver power. S.R. No. 167/2015 reg. 13(7). Authorised by the Chief Parliamentary Counsel 166 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 32—High efficiency refrigerated display cabinet Schedule 32—High efficiency Sch. 32 (Heading) refrigerated display cabinet amended by S.R. No. Regulation 6(3)(b) 167/2015 reg. 14(1)(a). Prescribed activity under regulation 6(3)(b): Installing a refrigerated display Sch. 32 cabinet that complies with the criteria specified in Part A of Schedule 32. inserted by S.R. No. 32/2012 Part A—Criteria reg. 38, amended by Item S.R. No. 167/2015 reg. 14(1)(b). 32A A refrigerated display cabinet that is— Sch. 32 Pt A item 32A substituted by (a) rated as 'high efficiency' within the meaning of S.R. No. AS 1731.14-2003 published on 1 October 2003 167/2015 reg. 14(2). and reissued July 2012 incorporating Amendment No. 2 when tested in accordance with— (i) AS 1731.9-2003 published on 1 October 2003 and reissued December 2005 incorporating Amendment No. 1; and (ii) AS 1731.12-2003 published on 1 October 2003 and reissued December 2005 incorporating Amendment No. 1; and (b) listed on the ESC register. Sch. 32 Pt B Part B—Calculation of carbon dioxide amended by S.R. No. equivalents of greenhouse gases 167/2015 reg. 14(3). The carbon dioxide equivalent (in tonnes) of greenhouse gases to be reduced by the installation of a product referred to in an item in Part A is calculated by multiplying the total display area (m2) of that item by the abatement factor for that item and by the regional factor applying to the place where the product is installed. Authorised by the Chief Parliamentary Counsel 167 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 32—High efficiency refrigerated display cabinet The following are the abatement factors and regional factors for each item in Part A: Item 32A The abatement factor for a refrigerated display cabinet is specified in column 3 of the following Table in respect of the type and subclass (within the meaning of Appendix A of AS 1731.14-2003 published on 1 October 2003 and reissued July 2012 incorporating Amendment No. 2) of the refrigerated display cabinet, as specified in column 2 of that Table. Sch. 32 Pt B Column 1 Column 2 Column 3 item 32A (Table) Refrigerated display cabinet amended by Item type and subclass Abatement factor S.R. No. 167/2015 1 RS 1- unlit shelves 10∙69 reg. 14(4). 2 RS 1- lit shelves 18∙19 3 RS 2- unlit shelves 10∙80 4 RS 2- lit shelves 14∙44 5 RS 3- unlit shelves 11∙60 6 RS 3- lit shelves 15∙69 7 RS 4- glass door 7∙62 8 RS 6- gravity coil 11∙03 9 RS 6- fan coil 11∙03 10 RS 7- fan coil 12∙62 11 RS 8- gravity coil 9∙55 12 RS 8- fan coil 10∙23 13 RS 9- fan coil 10∙35 14 RS 10- low 14∙55 15 RS 11 29∙68 16 RS 12 51∙62 17 RS 13- solid sided 16∙60 18 RS 13- glass sided 15∙24 19 RS 14- solid sided 10∙35 Authorised by the Chief Parliamentary Counsel 168 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 32—High efficiency refrigerated display cabinet Column 1 Column 2 Column 3 Refrigerated display cabinet Item type and subclass Abatement factor 20 RS 14- glass sided 61∙97 21 RS 15- glass door 24∙79 22 RS 16- glass door 27∙06 23 RS 18 22∙63 24 RS 19 16∙83 25 HC 1 7∙73 26 HC 4 10∙46 27 VC 1 22∙17 28 VC 2 17∙62 29 VC4- solid door 25∙47 30 VC4- glass door 16∙71 31 HF4 17∙97 32 HF6 5∙34 33 VF4- solid door 27∙97 34 VF4- glass door 27∙97 32A Regional factor: (a) If the product is installed in metropolitan Victoria: 0·98; (b) If the product is installed in regional Victoria: 1·04. Sch. 32 Pt C Part C—Time at which activity (Heading) substituted by undertaken and reduction in greenhouse S.R. No. 96/2013 reg. 8. gas emissions occurs Item 32A At the beginning of the day on which the installed product Sch. 32 Pt C item 32A is first able to deliver refrigeration. substituted by S.R. No. 167/2015 reg. 14(5). Authorised by the Chief Parliamentary Counsel 169 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 33—Refrigeration fan motor Sch. 33 (Heading) Schedule 33—Refrigeration fan motor amended by Regulation 6(3)(c) S.R. No. 167/2015 Prescribed activity under regulation 6(3)(c): Installing a product that reg. 15(1)(a). complies with the criteria specified in Part A of Schedule 33 in a refrigerated Sch. 33 display cabinet, commercial freezer or cool room. inserted by S.R. No. 32/2012 Part A—Criteria reg. 38, amended by Item S.R. No. 167/2015 reg. 15(1)(b). Sch. 33 Pt A 33A A fan that is powered by an electronically commutated item 33A substituted by motor (being a permanent magnet motor with electronic S.R. No. commutation) that is listed in the ESC register and— 167/2015 reg. 15(2). (a) in the case of an internal rotor motor, has a rated motor output of not more than 600 watts; or (b) in the case of an external rotor motor, has a rated motor input of not more than 800 watts. Sch. 33 Pt B amended by Part B—Calculation of carbon dioxide S.R. No. 167/2015 equivalents of greenhouse gases reg. 15(3). The carbon dioxide equivalent (in tonnes) of greenhouse gases to be reduced by the installation of a product referred to in an item in Part A is calculated by multiplying the abatement factor of that item by the regional factor applying to the place where the product is installed. The following is the abatement factor and regional factor for each item in Part A: Item 33A Abatement factor: To be determined in accordance with the formula— (IP × 0.7692 + 19.385) × (1 + (1 ÷ COP)) × 0.03357 Authorised by the Chief Parliamentary Counsel 170 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008

Schedule 33—Refrigeration fan motor Where— IP is the input power in watts of the motor that powers the fan; COP is the coefficient of performance for the refrigerator in which the fan is installed, as specified in column 3 of the following Table in respect of the type of the refrigerator, as specified in column 2 of that Table. Column 1 Column 2 Column 3 Item Refrigerator type COP 1 Refrigerator display cabinet 2·80 2 Freezer 1·80 3 Cool room 2·56 33A Regional factor: (a) If the product or products are installed in metropolitan Victoria: 0·98; (b) If the product or products are installed in regional Victoria: 1·04. Sch. 33 Pt C Part C—Time at which activity (Heading) substituted by undertaken and reduction in greenhouse S.R. No. 96/2013 reg. 8. gas emissions occurs Item 33A At the beginning of the day on which the installed motor is Sch. 33 Pt C item 33A first able to deliver power to the installed fan. substituted by S.R. No. 167/2015 reg. 15(4). Authorised by the Chief Parliamentary Counsel 171 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 34—Lighting upgrade Sch. 34 inserted by Schedule 34—Lighting upgrade S.R. No. Regulation 6(2)(d) and (3)(d) 32/2012 reg. 38. Prescribed activities under regulation 6(2)(d) and (3)(d): Undertaking a lighting upgrade in certain buildings, structures or areas by installing lighting equipment referred to in Part A of Schedule 34 and decommissioning any replaced lighting equipment, or doing certain things to a multiple lamp fitting. Sch. 34 Pt A items 34A– Part A—Criteria 34D substituted by Item S.R. No. 167/2015 34A A T5 adaptor that— reg. 16(1). (a) has a lamp with a minimum wattage of 14 watts; and (b) has a power factor of at least 0∙9; and (c) has a ballast made from rigid non-metallic material; and (d) meets standards determined by the ESC when tested by an approved laboratory in accordance with a laboratory test approved by the ESC; and (e) is listed in the ESC register. 34B A lighting control device, other than a voltage reduction unit, that is certified by the manufacturer as appropriate for use with the type of lamps it will be required to control. 34C A voltage reduction unit that— (a) has an output voltage ascertained by an approved laboratory in accordance with a laboratory test approved by the ESC; and (b) is not installed in conjunction with electronic ballasts; and (c) is listed in the ESC register. Authorised by the Chief Parliamentary Counsel 172 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 34—Lighting upgrade 34D Any other lighting equipment that— (a) is listed in the ESC register; and (b) when installed, meets the minimum power factor determined by the ESC and specified on the ESC's Internet site; and (c) meets standards determined by the ESC when tested by an approved laboratory in accordance with a laboratory test approved by the ESC. Sch. 34 Pt B Part B—Calculation of carbon dioxide amended by S.R. No. equivalents of greenhouse gases 167/2015 reg. 16(2)–(5). The carbon dioxide equivalent (in tonnes) of greenhouse gases to be reduced by undertaking a lighting upgrade is determined by multiplying the abatement factor for the lighting upgrade by the regional factor for the lighting upgrade. Abatement factor The abatement factor for a lighting upgrade is calculated by multiplying the energy savings by 1∙095, where energy savings are calculated using equation 1. Equation 1 Energy savings = baseline energy consumption - upgrade energy consumption where— baseline energy consumption is in MWh and is calculated— (a) if the lighting upgrade is part of a site refurbishment that is required to comply with Part J6 of the Building Code as amended from time to time, using Equation 2; or (b) in any other case, using Equation 3; upgrade energy consumption is in MWh, and is calculated using Equation 4. Authorised by the Chief Parliamentary Counsel 173 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 34—Lighting upgrade Equation 2 Baseline Energy Consumption (MWh)= Σ Each Space ( IPD × Area × Asset Lifetime × Annual Operating Hours × CM × AM ) ÷106 where— Each Space means each space within the site of the lighting upgrade that requires a different illumination power density (IPD) within the meaning of Part J6 of the Building Code as amended from time to time; IPD is the maximum allowable illumination power density for the space (in watts/m2), as specified by Table J6.2a of the Building Code as amended from time to time; Area is the area of the space in m2; Asset Lifetime is— (a) if, as part of the lighting upgrade— (i) a light fitting, ballast or transformer (and any associated lamp or reflector) is installed in the space; and (ii) no lighting equipment of any other type (other than a lighting control device) is installed in the space— 10 years; or (ab) if, as part of the lighting upgrade— (i) a lighting control device is installed in the space; and (ii) no lighting equipment of any other type is installed in the space— 5 years; or (b) if, as part of the lighting upgrade— (i) no more than half the lamps are removed from a multiple lamp fitting in the space; and (ii) any ballast or transformer associated with the removed lamps is decommissioned; and Authorised by the Chief Parliamentary Counsel 174 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 34—Lighting upgrade (iii) no light fittings, ballasts, transformers, lamps or T5 adaptors are installed in the space— the lowest manufacturer's rated lifetime (in hours and not exceeding 30 000 hours) for a lamp that is in the space before the lighting upgrade is undertaken divided by Annual Operating Hours, to a maximum of 10 years; or (c) in any other case, the lowest manufacturer's rated lifetime (in hours and not exceeding 30 000 hours) for a lamp that is in the space after the lighting upgrade is undertaken divided by Annual Operating Hours, to a maximum of 10 years; Annual Operating Hours is— (a) if the lighting upgrade is undertaken on a road or in a public or outdoor space that is not a sports field, other than the replacement or installation of traffic signals, 4500 hours; or (b) if traffic signals are replaced as part of the lighting upgrade, 2920 hours; or (c) if the lighting upgrade is undertaken in a space specified in column 2 of Table 3, the number of hours specified in column 3 of that Table in respect of that space as specified in column 2 of that Table; or (d) if the lighting upgrade is undertaken in a space that is not specified in column 2 of Table 3 but that is specified in column 2 of Table 4, the number of hours specified in column 3 of Table 4 in respect of that space as specified in column 2 of that Table; or (e) in any other case, 1000 hours. CM is the control multiplier for the space, being— (a) if no lighting control device is installed in respect of light fittings in that space, 1; or Authorised by the Chief Parliamentary Counsel 175 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 34—Lighting upgrade (b) if one type of lighting control device is installed in respect of light fittings in that space, the number specified in column 3 of Table 2 in respect of the type of the lighting control device as specified in column 2 of that Table; or (c) if more than one type of lighting control device is installed in respect of light fittings in that space— (i) the product of the two lowest numbers specified in column 3 of Table 2 in respect of the types of those lighting control devices as specified in column 2 of that Table; or (ii) if the product referred to in subparagraph (i) is lower than 0·6, 0·6; AM is the air conditioning multiplier, being— (a) if the space is air conditioned, 1·05; or (b) if the space is not air conditioned, 1. Equation 3 Baseline energy consumption (MWh) = Σ Each Incumbent Lamp (LCP × Asset Lifetime × Annual Operating Hours × CM × AM ) ÷106 where— Each Incumbent Lamp means each lamp and associated ballast and transformer (if any) in the site of the lighting upgrade before the lighting upgrade is undertaken; LCP means the lamp circuit power for the lamp, being— (a) if the ESC has determined the lamp circuit power for the type of the lamp in relation to the lighting upgrade in accordance with regulation 6C(2), the lamp circuit power determined by the ESC; or (b) in any other case, the value specified in column 3 of Table 1 of this Schedule in respect of the type of the lamp as specified in column 2 of that Table; Authorised by the Chief Parliamentary Counsel 176 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 34—Lighting upgrade Asset Lifetime is— (a) if, as part of the lighting upgrade— (i) the lamp is removed from a multiple lamp fitting from which no more than half of the installed lamps are removed; and (ii) any ballast or transformer associated with the removed lamps is decommissioned— the manufacturer's rated lifetime (in hours and not exceeding 30 000 hours) for the lamp divided by Annual Operating Hours, to a maximum of 10 years; or (ab) if, as part of the lighting upgrade— (i) a lighting control device is installed in the space; and (ii) no lighting equipment of any other type is installed in the space— 5 years; or (b) if, as part of the lighting upgrade, the lamp is removed and not replaced and— (i) the ballast or transformer associated with the lamp is replaced; or (ii) the light fitting in which the lamp was installed is removed— 10 years; or (c) if, as part of the lighting upgrade, the lamp is replaced and any ballast or transformer associated with the lamp is also replaced, 10 years; or (d) if, as part of the lighting upgrade, the lamp is replaced and— (i) the ballast or transformer associated with the lamp is not replaced; or Authorised by the Chief Parliamentary Counsel 177 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 34—Lighting upgrade (ii) there is no ballast or transformer associated with the lamp— the manufacturer's rated lifetime (in hours and not exceeding 30 000 hours) for the replacement lamp divided by Annual Operating Hours, to a maximum of 10 years; or (e) in any other case, the manufacturer's rated lifetime (in hours and not exceeding 30 000 hours) for the lamp divided by Annual Operating Hours, to a maximum of 10 years; Annual Operating Hours is— (a) if the lighting upgrade is undertaken on a road or in a public or outdoor space that is not a sports field, other than the replacement or installation of traffic signals, 4500 hours; or (b) if traffic signals are replaced as part of the lighting upgrade, 2920 hours; or (c) if the lighting upgrade is undertaken in a space specified in column 2 of Table 3, the number of hours specified in column 3 of that Table in respect of that space as specified in column 2 of that Table; or (d) if the lighting upgrade is undertaken in a space that is not specified in column 2 of Table 3 but that is specified in column 2 of Table 4, the number of hours specified in column 3 of Table 4 in respect of that space as specified in column 2 of that Table; or (e) in any other case, 1000 hours. CM is the control multiplier for the lamp, being— (a) if no lighting control device is installed in respect of the lamp, 1; or (b) if one type of lighting control device is installed in respect of the lamp, the number specified in column 3 of Table 2 in respect of the type of the lighting control device as specified in column 2 of that Table; or Authorised by the Chief Parliamentary Counsel 178 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 34—Lighting upgrade (c) if more than one type of lighting control device is installed in respect of the lamp— (i) the product of the two lowest numbers specified in column 3 of Table 2 in respect of the types of those lighting control devices as specified in column 2 of that Table; or (ii) if the product referred to in subparagraph (i) is lower than 0·6, 0·6; AM is the air conditioning multiplier, being— (a) if the lamp is in a space that is air conditioned, 1·05; or (b) if the lamp is in a space that is not air conditioned, 1. Equation 4 Upgrade energy consumption (MWh) = Σ Each Upgrade Lamp (LCP × Asset Lifetime × Annual Operating Hours × CM × AM ) ÷106 where— Each Upgrade Lamp means each lamp and associated ballast and transformer (if any) in the site of the lighting upgrade after the prescribed activity is undertaken; LCP means the lamp circuit power for the lamp, being— (a) if the ESC has determined the lamp circuit power for the type of the lamp in relation to the lighting upgrade in accordance with regulation 6C(2), the lamp circuit power determined by the ESC; or (b) in any other case, the value specified in column 4 of Table 1 of this Schedule in respect of the type of the lamp as specified in column 2 of that Table; Asset Lifetime is— (a) if the ballast or transformer associated with the lamp is replaced as part of the lighting upgrade, 10 years; or Authorised by the Chief Parliamentary Counsel 179 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 34—Lighting upgrade (ab) if, as part of the lighting upgrade— (i) a lighting control device is installed in the space; and (ii) no lighting equipment of any other type is installed in the space— 5 years; or; (b) if the lamp is installed in a lighting fitting that was installed as part of the lighting upgrade, 10 years; or (c) in any other case, the manufacturer's rated lifetime (in hours and not exceeding 30 000 hours) for the lamp divided by Annual Operating Hours, to a maximum of 10 years; Annual Operating Hours is— (a) if the lighting upgrade is undertaken on a road or in a public or outdoor space that is not a sports field, other than the replacement or installation of traffic signals, 4500 hours; or (b) if traffic signals are replaced as part of the lighting upgrade, 2920 hours; or (c) if the lighting upgrade is undertaken in a space specified in column 2 of Table 3, the number of hours specified in column 3 of that Table in respect of that space as specified in column 2 of that Table; or (d) if the lighting upgrade is undertaken in a space that is not specified in column 2 of Table 3 but that is specified in column 2 of Table 4, the number of hours specified in column 3 of Table 4 in respect of that space as specified in column 2 of that Table; or (e) in any other case, 1000 hours. CM is the control multiplier for the lamp, being— (a) if no lighting control device is installed in respect of the lamp, 1; or Authorised by the Chief Parliamentary Counsel 180 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 34—Lighting upgrade (b) if one type of lighting control device is installed in respect of the lamp, the number specified in column 3 of Table 2 in respect of the type of the lighting control device as specified in column 2 of that Table; or (c) if more than one type of lighting control device is installed in respect of the lamp— (i) the product of the two lowest numbers specified in column 3 of Table 2 in respect of the types of those lighting control devices as specified in column 2 of that Table; or (ii) if the product referred to in subparagraph (i) is lower than 0·6, 0·6; AM is the air conditioning multiplier, being— (a) if the lamp is in a space that is air conditioned, 1·05; or (b) if the lamp is in a space that is not air conditioned, 1. Table 1—Lamp circuit power Column 1 Column 2 Column 3 Column 4 Type of incumbent lamp or upgrade Lamp circuit power Lamp circuit power Item lamp for incumbent lamp for upgrade lamp 1 T8 or T12 linear NLP +2 NLP +2 fluorescent or circular fluorescent with an associated ballast marked as having a EEI of A1 2 T8 or T12 linear NLP NLP fluorescent or circular fluorescent with an associated ballast marked as having a EEI of A2 Authorised by the Chief Parliamentary Counsel 181 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 34—Lighting upgrade Column 1 Column 2 Column 3 Column 4 Type of incumbent lamp or upgrade Lamp circuit power Lamp circuit power Item lamp for incumbent lamp for upgrade lamp 3 T8 or T12 linear NLP + 2 NLP + 2 fluorescent or circular fluorescent with an associated ballast marked as having a EEI of A3 4 T8 or T12 linear NLP + 6 NLP + 6 fluorescent or circular fluorescent with an associated ballast rated as having a EEI of B1 5 T8 or T12 linear NLP + 8 NLP + 8 fluorescent or circular fluorescent with an associated ballast marked as having a EEI of B2 6 T8 or T12 linear NLP + 10 NLP + 10 fluorescent or circular fluorescent with an associated ballast marked as having a EEI of C 7 T8 or T12 linear NLP + 12 NLP + 12 fluorescent or circular fluorescent with an associated ballast marked as having a EEI of D Authorised by the Chief Parliamentary Counsel 182 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 34—Lighting upgrade Column 1 Column 2 Column 3 Column 4 Type of incumbent lamp or upgrade Lamp circuit power Lamp circuit power Item lamp for incumbent lamp for upgrade lamp 8 T8 or T12 linear NLP + 10 NLP + 10 fluorescent or circular fluorescent with an associated magnetic ballast on which no EEI is marked 9 T8 or T12 linear NLP + 2 NLP + 2 fluorescent or circular fluorescent with an associated electronic ballast on which no EEI is marked 10 T5 linear 1·13 × NLP + 2·5 1·13 × NLP + 2·5 fluorescent or circular fluorescent with an associated ballast marked as having a EEI of A1 11 T5 linear 1·08 × NLP + 1·5 1·08 × NLP + 1·5 fluorescent or circular fluorescent with an associated ballast marked as having a EEI of A2 12 T5 linear 1·13 × NLP + 2·5 1·13 × NLP + 2·5 fluorescent or circular fluorescent with an associated ballast marked as having a EEI of A3 Authorised by the Chief Parliamentary Counsel 183 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 34—Lighting upgrade Column 1 Column 2 Column 3 Column 4 Type of incumbent lamp or upgrade Lamp circuit power Lamp circuit power Item lamp for incumbent lamp for upgrade lamp 13 T5 linear 1·13 ×NLP + 2·5 1·13 × NLP + 2·5 fluorescent or circular fluorescent with an associated electronic ballast on which no EEI is marked 14 Compact NLP + 3 NLP + 3 fluorescent lamp with non-integral ballast marked as having a EEI of A1 15 Compact NLP + 1 NLP + 1 fluorescent lamp with non-integral ballast marked as having a EEI of A2 16 Compact NLP + 3 NLP + 3 fluorescent lamp with non-integral ballast marked as having a EEI of A3 17 Compact NLP + 5 NLP + 5 fluorescent lamp with non-integral ballast marked as having a EEI of B1 18 Compact NLP + 7 NLP + 7 fluorescent lamp with non-integral ballast marked as having a EEI of B2 Authorised by the Chief Parliamentary Counsel 184 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 34—Lighting upgrade Column 1 Column 2 Column 3 Column 4 Type of incumbent lamp or upgrade Lamp circuit power Lamp circuit power Item lamp for incumbent lamp for upgrade lamp 19 Compact NLP + 9 NLP + 9 fluorescent lamp with non-integral ballast marked as having a EEI of C 20 Compact NLP + 11 NLP + 11 fluorescent lamp with non-integral ballast marked as having a EEI of D 21 Compact NLP + 9 NLP + 9 fluorescent lamp with non-integral magnetic ballast on which no EEI is marked 22 Compact NLP + 3 NLP + 3 fluorescent lamp with non-integral electronic ballast on which no EEI is marked 23 Compact NLP NLP fluorescent with integral ballast 24 Tungsten NLP × 0·7 NLP incandescent or halogen (mains voltage) 25 Tungsten NLP (being no NLP ÷ 0·8 incandescent or greater than halogen (extra 37 watts) ÷ 0·8 low voltage) with magnetic transformer Authorised by the Chief Parliamentary Counsel 185 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 34—Lighting upgrade Column 1 Column 2 Column 3 Column 4 Type of incumbent lamp or upgrade Lamp circuit power Lamp circuit power Item lamp for incumbent lamp for upgrade lamp 26 Tungsten NLP (being no NLP ÷ 0·93 incandescent or greater than halogen (extra 37 watts) ÷ 0·93 low voltage) with electronic transformer 27 Metal halide with 1·0456 ×NLP + 14 1·0456 × NLP + 14 magnetic ballast (reactor type) 28 Metal halide with 1·071 ×NLP + 22 1·071 × NLP + 22 magnetic ballast (constant wattage type) 29 Metal halide with 1·096 ×NLP + 0·9 1·096 × NLP + 0·9 electronic ballast 30 Mercury vapour 1·033 ×NLP + 11 1·033 × NLP + 11 with magnetic ballast 31 High pressure 1·051 ×NLP + 13 1·051 × NLP + 13 sodium (HPS) with magnetic ballast Notes 1 EEI means Energy Efficiency Index within the meaning of AS/NZS 4783.2:2002 published on 23 December 2002. 2 NLP means the nominal lamp power, being the manufacturer's rated value for power drawn by a single lamp. 3 If the lamp circuit power of a lamp of a type not listed in column 1 is required to calculate the abatement factor, no certificate can be created in relation to the upgrade unless the ESC has determined the lamp circuit power for that type of lamp under regulation 6C(2). See regulation 10(3). Authorised by the Chief Parliamentary Counsel 186 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 34—Lighting upgrade Table 2—Control multiplier Sch. 34 Pt B (Table 2) Column 1 Column 2 Column 3 amended by S.R. No. Item Lighting control device Control multiplier 167/2015 reg. 16(6). 1 Occupancy sensor 0·7 2 Daylight-linked control 0·7 3 Programmable dimmer 0·85 4 Manual dimmer 0·9 5 Voltage reduction unit V2 ÷ 2402 where 'V' is the output voltage of the voltage reduction unit referred to in item 34C(a) of Part A of this Schedule. 6 Multiple Control 0∙76 Systems—where all lamps in the lighting system are connected to a programmable dimmer and manual dimmer 7 Multiple Control 0∙6 Systems—any other combination of 2 or more control systems above Table 3—Operating hours for lighting upgrades undertaken Sch. 34 Pt B (Table 3) in certain spaces inserted by S.R. No. Column 1 Column 2 Column 3 167/2015 reg. 16(7). Annual operating hours Item Type of space (hours per year) 1 Auditorium, church and public hall 2000 2 Board room and conference room 3000 3 Carpark—general (undercover) and 7000 carpark—entry zone (first 20 m of travel) 4 Carpark—general 4500 (open air) Authorised by the Chief Parliamentary Counsel 187 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 34—Lighting upgrade Column 1 Column 2 Column 3 Annual operating hours Item Type of space (hours per year) 5 Common rooms, spaces and corridors in 7000 a Class 2 building 6 Courtroom 2000 7 Dormitory of a Class 3 building used for 3000 sleeping only or sleeping and study 8 Health-care—children's ward, 6000 examination room, patient ward, all patient care areas including corridors where cyanosis lamps are used 9 Laboratory—artificially lit to an ambient 3000 level of 400 lx or more 10 Library—stack and shelving area, 3000 reading room and general areas 11 Lounge area for communal use in a 7000 Class 3 building or Class 9c aged care building 12 Maintained emergency lighting 8500 13 Museum and gallery—circulation, 2000 cleaning and service lighting 14 Office 3000 15 Restaurant, café, bar, hotel lounge and a 5000 space for the serving and consumption of food or drinks 16 Retail space including a museum and 5000 gallery whose purpose is the sale of objects 17 School—general purpose learning areas 3000 and tutorial rooms 18 Sole-occupancy unit of a Class 3 3000 building 19 Sole-occupancy unit of a Class 9c aged 6000 care building 20 Storage with shelving no higher than 5000 75% of the height of the aisle lighting Authorised by the Chief Parliamentary Counsel 188 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 34—Lighting upgrade Column 1 Column 2 Column 3 Annual operating hours Item Type of space (hours per year) 21 Storage with shelving higher than 75% 5000 of the height of the aisle lighting 22 Wholesale storage and display area 5000 Table 4—Operating hours determined by reference to Sch. 34 Pt B (Table 4) building classification under the Building Code inserted by S.R. No. Column 1 Column 2 Column 3 167/2015 reg. 16(7). Annual operating hours Item Type of space (hours per year) 1 A space in the common area of a 7000 building that is classified as Class 2 under Part 3A of the Building Code as amended from time to time 2 A space in the common area of a 7000 building that is classified as Class 3 under Part 3A of the Building Code as amended from time to time 3 A space in a building that is classified as 3000 Class 3 under Part 3A of the Building Code as amended from time to time (other than a space in the common area of the building) 4 A space in a building that is classified as 3000 Class 5 under Part 3A of the Building Code as amended from time to time 5 A space in a building that is classified as 5000 Class 6 under Part 3A of the Building Code as amended from time to time 6 A space in an open air car park that is 4500 classified as Class 7a under Part 3A of the Building Code as amended from time to time Authorised by the Chief Parliamentary Counsel 189 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 34—Lighting upgrade Column 1 Column 2 Column 3 Annual operating hours Item Type of space (hours per year) 7 A space in a car park (other than an open 7000 air car park) that is classified as Class 7a under Part 3A of the Building Code as amended from time to time 8 A space in a building that is classified as 5000 Class 7b under Part 3A of the Building Code as amended from time to time 9 A space in a laboratory or building that is 5000 classified as Class 8 under Part 3A of the Building Code as amended from time to time and that is also classified as Division C in the Australian and New Zealand Standard Industrial Classification issued on 26 June 2013 10 A space in a laboratory or building that 3000 is classified as Class 8 under Part 3A of the Building Code as amended from time to time and that is not classified as Division C in the Australian and New Zealand Standard Industrial Classification issued on 26 June 2013 11 A space in a building that is classified as 6000 Class 9a under Part 3A of the Building Code as amended from time to time 12 A space in a building that is classified as 2000 Class 9b under Part 3A of the Building Code as amended from time to time 13 A space in a building that is classified as 6000 Class 9c under Part 3A of the Building Code as amended from time to time 14 A space in a structure that is classified as 1000 Class 10b under Part 3A of the Building Code as amended from time to time Authorised by the Chief Parliamentary Counsel 190 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 34—Lighting upgrade Regional factor The regional factor for a lighting upgrade is— (a) if the lighting upgrade is undertaken in metropolitan Victoria, 0·98; (b) if the lighting upgrade is undertaken in regional Victoria, 1·04. Sch. 34 Pt C Part C—Time at which activity (Heading) substituted by undertaken and reduction in greenhouse S.R. No. 96/2013 reg. 8. gas emissions occurs At the beginning of the day on which the lighting upgrade is completed. Authorised by the Chief Parliamentary Counsel 191 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 35—Low flow trigger nozzle Sch. 35 inserted by Schedule 35—Low flow trigger nozzle S.R. No. Regulation 6(3)(e) 24/2013 reg. 9. Prescribed activity under regulation 6(3)(e): Decommissioning a trigger nozzle that has a maximum water flow requirement of at least 12L/minute and that is not labelled with a Smart Approved Watermark and installing a trigger nozzle that complies with the criteria specified in Part A of Schedule 35. Part A—Criteria 35A A trigger nozzle that— (a) is labelled with a Smart Approved Watermark; and (b) only uses water with a temperature of at least 45°C. Part B—Calculation of carbon dioxide equivalents of greenhouse gases The carbon dioxide equivalent (in tonnes) of greenhouse gases to be reduced by decommissioning a trigger nozzle that has a maximum water flow requirement of at least 12L/minute and that is not labelled with a Smart Approved Watermark and installing a product referred to in Part A is calculated by multiplying the abatement factor for that item by the regional factor applying to the place where the product is installed. The following are the abatement factors and regional factors for each item in Part A: Item 35A Abatement factor 1·42. 35A Regional factor: (a) If the product is installed in metropolitan Victoria: 0·85; (b) If the product is installed in regional Victoria: 1·40. Authorised by the Chief Parliamentary Counsel 192 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008

Schedule 35—Low flow trigger nozzle Part C—Time at which activity Sch. 35 Pt C (Heading) undertaken and reduction in greenhouse substituted by S.R. No. gas emissions occurs 96/2013 reg. 8. Item 35A At the beginning of the later of the following days— (a) the day on which the installation is completed; or (b) the day on which the replaced trigger nozzle is decommissioned. Authorised by the Chief Parliamentary Counsel 193 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 36—Water efficient prerinse spray valve Sch. 36 inserted by Schedule 36—Water efficient prerinse S.R. No. 24/2013 reg. 9. spray valve Regulation 6(3)(f) and (g) Prescribed activity under regulation 6(3)(f) and(g): Installing a prerinse spray valve that complies with the criteria specified in Part A of Schedule 36 on an existing fitting for a prerinse spray valve on which no prerinse spray valve was previously installed, or decommissioning a prerinse spray valve that is not rated as having a 4 star or higher water efficiency when assessed and labelled in accordance with AS/NZS 6400:2005 reissued in June 2011 and installing a prerinse spray valve that complies with the criteria specified in Part A of Schedule 36. Part A—Criteria 36A A prerinse spray valve that— (a) is rated as having a minimum 6 star water efficiency rating when assessed and labelled in accordance with AS/NZS 6400:2005 reissued in June 2011; and (b) has a cleanability score of 26 seconds or less when tested in accordance with ASTM F2324-03. Part B—Calculation of carbon dioxide equivalents of greenhouse gases The carbon dioxide equivalent (in tonnes) of greenhouse gases to be reduced by either— (a) installing a prerinse spray valve that complies with the criteria specified in Part A on an existing fitting for a prerinse spray valve on which no prerinse spray valve was previously installed; or Authorised by the Chief Parliamentary Counsel 194 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008

Schedule 36—Water efficient prerinse spray valve (b) decommissioning a prerinse spray valve that is not rated as having a 4 star or higher water efficiency (when assessed and labelled in accordance with AS/NZS 6400:2005 reissued in June 2011) and installing a prerinse spray valve that complies with the criteria specified in Part A— is calculated by multiplying the abatement factor for that item by the regional factor applying to the place where the product is installed. The following are the abatement factors and regional factors for each item in Part A: Item 36A Abatement factor: 2·99. 36A Regional factor: (a) If the product is installed in metropolitan Victoria: 0·85; (b) If the product is installed in regional Victoria: 1·40. Sch. 36 Pt C Part C—Time at which activity (Heading) substituted by undertaken and reduction in greenhouse S.R. No. 96/2013 reg. 8. gas emissions occurs Item 36A At the beginning of the later of the following days— (a) the day on which the installation is completed; or (b) the day on which the replaced prerinse spray valve (if any) is decommissioned. Authorised by the Chief Parliamentary Counsel 195 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 37—Scheduled activity premises Sch. 37 inserted by Schedule 37—Scheduled activity premises S.R. No. Regulation 4 71/2017 reg. 9. Part 1—Specified addresses Column 1 Column 2 Item Specified addresses 1 1 Hume Road, LAVERTON NORTH, VIC, 3026 2 631 Kororoit Creek Road, ALTONA, VIC, 3018 3 606 Madeira Packet Road, PORTLAND, VIC, 3305 4 55 Commercial Road, MELBOURNE, VIC, 3004 5 1 Crosher Lane, WANGARATTA, VIC, 3677 6 1420 Ferntree Gully Road, SCORESBY, VIC, 3179 7 334C River Road, SWAN HILL, VIC, 3585 8 145 Studley Road, HEIDELBERG, VIC, 3084 9 330 Waterdale Road, HEIDELBERG WEST, VIC, 3081 10 Lot 1074 Boonoonar Road, COLIGNAN, VIC, 3494 11 65 Leakes Road, LAVERTON NORTH, VIC, 3026 12 17–19 Pipe Road, LAVERTON NORTH, VIC, 3026 13 10 Woolshed Gully Drive, MOUNT CLEAR, VIC, 3350 14 45–47 Mackey Street, NORTH GEELONG, VIC, 3215 15 272–322 Ryrie Street, GEELONG, VIC, 3220 16 159 Burgins Road, HAMILTON, VIC, 3300 17 5096 Murray Valley Highway, STRATHMERTON, VIC, 3641 18 28 Bayview Road, HASTINGS, VIC, 3915 19 351 Hammond Road, DANDENONG SOUTH, VIC, 3175 20 226 Lorimer Street, PORT MELBOURNE, VIC, 3207 21 676 Lorimer Street, PORT MELBOURNE, VIC, 3207 22 2 Trawalla Avenue, THOMASTOWN, VIC, 3074 Authorised by the Chief Parliamentary Counsel 196 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 37—Scheduled activity premises Column 1 Column 2 Item Specified addresses 23 191 George Street, WANTIRNA SOUTH, VIC, 3152 24 170 Reservoir Road, WAURN PONDS, VIC, 3216 25 24 Queen Street, WODONGA, VIC, 3690 26 19–81 Sisely Avenue, WANGARATTA, VIC, 3677 27 47 Station Street, KORUMBURRA, VIC, 3950 28 183 Wattletree Road, MALVERN, VIC, 3144 29 55 Lemnos North Road, LEMNOS, VIC, 3631 30 425 Somerville Road, TOTTENHAM, VIC, 3012 31 380 Tramway Road, MORWELL, VIC, 3840 32 251 Myrtleford-Yackandandah Road, MYRTLEFORD, VIC, 3737 33 224 Yeungroon-Woosang Road, YEUNGROON EAST, VIC, 3525 34 246 East Boundary Road, BENTLEIGH EAST, VIC, 3165 35 20 Levanswell Road, MOORABBIN, VIC, 3189 36 1341 Dandenong Road, CHADSTONE, VIC, 3148 37 171 Fitzgerald Road, LAVERTON NORTH, VIC, 3026 38 1 Tristania Drive, COLAC, VIC, 3250 39 8 Whiteman Street, SOUTHBANK, VIC, 3006 40 1126 Sydney Road, FAWKNER, VIC, 3060 41 5 Portarlington Road, EAST GEELONG, VIC, 3220 42 189–209 Camp Road, BROADMEADOWS, VIC, 3047 43 45 Poplar Road, PARKVILLE, VIC, 3052 44 656 Mitcham Road, VERMONT, VIC, 3133 45 277 Whitehall Street, YARRAVILLE, VIC, 3013 46 95 Greens Road, DANDENONG SOUTH, VIC, 3175 47 36–80 Church Street, ABBOTSFORD, VIC, 3067 48 541–583 Kororoit Creek Road, ALTONA, VIC, 3018 Authorised by the Chief Parliamentary Counsel 197 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 37—Scheduled activity premises Column 1 Column 2 Item Specified addresses 49 13 Bridge Street, NEWTOWN, VIC, 3220 50 37–41 Gilbertson Road, LAVERTON NORTH, VIC, 3026 51 412 Commercial Road, MORWELL, VIC, 3840 52 285 Waarre Road, WAARRE, VIC, 3269 53 Lot 50E Eastern Road, YALLOURN, VIC, 3825 54 33–35 Cemetery Road, HASTINGS, VIC, 3915 55 514 Garretts Road, LONGFORD, VIC, 3851 56 127 Frankston-Dandenong Road, DANDENONG, VIC, 3175 57 129 Curdie Street, COBDEN, VIC, 3266 58 15 Factory Road, COROROOKE, VIC, 3254 59 150 Darnum Park Road, DARNUM, VIC, 3822 60 50 Drummond Street, DENNINGTON, VIC, 3280 61 20 Midland Highway, STANHOPE, VIC, 3623 62 22–30 Denmark Road, ECHUCA, VIC, 3564 63 1735 Sydney Road, CAMPBELLFIELD, VIC, 3061 64 365–455 Melbourne Road, NORLANE, VIC, 3214 65 121–171 Seabeach Parade, NORTH SHORE, VIC, 3214 66 25–33 Fourth Avenue, SUNSHINE, VIC, 3020 67 940 Koo Wee Rup Road, PAKENHAM, VIC, 3810 68 170 South Gippsland Highway, DANDENONG, VIC, 3175 69 64 Richards Road, CASTLEMAINE, VIC, 3450 70 1061 Mountain Highway, BORONIA, VIC, 3155 71 191 Salmon Street, PORT MELBOURNE, VIC, 3207 72 7 Factories Road, SOUTH GEELONG, VIC, 3220 73 20 Heaths Court, MILL PARK, VIC, 3082 74 120–200 Rosamond Road, MARIBYRNONG, VIC, 3032 Authorised by the Chief Parliamentary Counsel 198 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 37—Scheduled activity premises Column 1 Column 2 Item Specified addresses 75 5331 Great Ocean Road, ALLANSFORD, VIC, 3277 76 2121 Finlay Road, TONGALA, VIC, 3621 77 504 Princes Highway, NOBLE PARK NORTH, VIC, 3174 78 74 Hazeldenes Road, LOCKWOOD, VIC, 3551 79 290 Oaklands Road, OAKLANDS JUNCTION, VIC, 3063 80 1 Lexia Place, MULGRAVE, VIC, 3170 81 77 Raglan Street, PRESTON, VIC, 3072 82 3610 Glenelg Highway, PITTONG, VIC, 3360 83 121 Grant Road, SOMERVILLE, VIC, 3912 84 1 Roberts Street, WEST FOOTSCRAY, VIC, 3012 85 30 Industry Park Drive, BROOKLYN, VIC, 3012 86 119 Racecourse Road, COBRAM, VIC, 3644 87 54 Cornelia Creek Road, ECHUCA, VIC, 3564 88 91–99 Ajax Road, ALTONA, VIC, 3018 89 323–351 Canterbury Road, RINGWOOD, VIC, 3134 90 32 Koornang Road, SCORESBY, VIC, 3179 91 162 Salmon Street, PORT MELBOURNE, VIC, 3207 92 2040 Hume Highway, CAMPBELLFIELD, VIC, 3061 93 8–10 Berends Drive, DANDENONG SOUTH, VIC, 3175 94 50 Baranduda Drive, BARANDUDA, VIC, 3691 95 150 Wells Road, CHELSEA HEIGHTS, VIC, 3196 96 1 National Road, MORWELL, VIC, 3840 97 32 Crowle Street, NORTH GEELONG, VIC, 3215 98 116 Ring Road, WENDOUREE, VIC, 3355 99 1 Petcare Place, WODONGA, VIC, 3690 100 1059 Ring Road, MITCHELL PARK, VIC, 3355 Authorised by the Chief Parliamentary Counsel 199 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 37—Scheduled activity premises Column 1 Column 2 Item Specified addresses 101 300 Grattan Street, PARKVILLE, VIC, 3050 102 40 Simpson Road, CHRISTMAS HILLS, VIC, 3775 103 165 Swinton Street, DENNINGTON, VIC, 3280 104 24 Scott Street, WARRNAMBOOL, VIC, 3280 105 15–29 The Crescent, MILDURA, VIC, 3500 106 351–381 Millers Road, ALTONA NORTH, VIC, 3025 107 765 Ballarat Road, DEER PARK, VIC, 3023 108 900 Dandenong Road, CAULFIELD EAST, VIC, 3145 109 1–131 Wellington Road, CLAYTON, VIC, 3800 110 42 Benalla-Yarrawonga Road, BENALLA, VIC, 3672 111 90 Broadway Street, COBRAM, VIC, 3644 112 23 Commercial Road, KOROIT, VIC, 3282 113 18 Yarragon Road, LEONGATHA, VIC, 3953 114 6–10 Bundalaguah Road, MAFFRA, VIC, 3860 115 69–87 Mackay Street, ROCHESTER, VIC, 3561 116 19 Kiewa East Road, TANGAMBALANGA, VIC, 3691 117 11 Nicholson Street, CARLTON, VIC, 3053 118 122 Lewis Road, WANTIRNA SOUTH, VIC, 3152 119 1585 Hume Highway, CAMPBELLFIELD, VIC, 3061 120 254–294 Wellington Road, MULGRAVE, VIC, 3170 121 13 Talbot Road, WAHGUNYAH, VIC, 3687 122 209–235 Frankston-Dandenong Road, DANDENONG SOUTH, VIC, 3175 123 600 Craigieburn Road East, CRAIGIEBURN, VIC, 3064 124 103–105 Pipe Road, LAVERTON NORTH, VIC, 3026 125 207 Sunshine Road, TOTTENHAM, VIC, 3012 126 1–35 Walchs Road, NORTH SHORE, VIC, 3214 Authorised by the Chief Parliamentary Counsel 200 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 37—Scheduled activity premises Column 1 Column 2 Item Specified addresses 127 166–180 Dohertys Road, LAVERTON NORTH, VIC, 3026 128 305 Waarre Road, WAARRE, VIC, 3269 129 93 Bannister Street, BENDIGO, VIC, 3550 130 842 Wellington Road, ROWVILLE, VIC, 3178 131 161–169 Princes Highway, BAIRNSDALE, VIC, 3875 132 21 Evans Street, BRAYBROOK, VIC, 3019 133 252 Chesterville Road, MOORABBIN, VIC, 3189 134 37–49 Browns Road, CLAYTON, VIC, 3168 135 100–102 Boundary Road, SUNSHINE WEST, VIC, 3020 136 14 McNaughton Road, CLAYTON, VIC, 3168 137 9–13 Rhur Street, DANDENONG SOUTH, VIC, 3175 138 471–513 Kororoit Creek Road, ALTONA, VIC, 3018 139 81–83 Fairbank Road, CLAYTON SOUTH, VIC, 3169 140 359 Bendigo-Tennyson Road, HUNTLY, VIC, 3551 141 46–50 McDonald Street, NUMURKAH, VIC, 3636 142 1555 Centre Road, CLAYTON, VIC, 3168 143 124 La Trobe Street, MELBOURNE, VIC, 3000 144 145 Fitzgerald Road, LAVERTON NORTH, VIC, 3026 145 70 Greg Norman Drive, POINT COOK, VIC, 3030 146 19 Ailsa Street, BOX HILL, VIC, 3128 147 2 Beverage Drive, TULLAMARINE, VIC, 3043 148 630 Howitt Street, BALLARAT, VIC, 3350 149 280 McIvor Highway, BENDIGO, VIC, 3550 150 90 Refinery Road, CORIO, VIC, 3214 151 870 McDonalds Track, LANG LANG, VIC, 3984 152 4 Melba Avenue, LILYDALE, VIC, 3140 153 2 Denmark Road, ECHUCA, VIC, 3564 Authorised by the Chief Parliamentary Counsel 201 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 37—Scheduled activity premises Column 1 Column 2 Item Specified addresses 154 28–46 Bald Hill Road, PAKENHAM, VIC, 3810 155 147–161 Cherry Lane, LAVERTON NORTH, VIC, 3026 156 246 Clayton Road, CLAYTON, VIC, 3168 157 135 David Street, DANDENONG, VIC, 3175 158 600 Princes Highway, SPRINGVALE, VIC, 3171 159 85 McCormick Road, KYABRAM, VIC, 3620 160 16 Young Street, MOOROOPNA, VIC, 3629 161 Andrew Fairley Avenue, SHEPPARTON, VIC, 3630 162 41 Victoria Parade, FITZROY, VIC, 3065 163 32 South Wharf, PORT MELBOURNE, VIC, 3207 164 265 Whitehall Street, YARRAVILLE, VIC, 3013 165 11 Moloney Drive, WODONGA, VIC, 3690 166 238 Hogan Street, TATURA, VIC, 3616 167 1816–1822 Dandenong Road, CLAYTON, VIC, 3168 168 300 Exhibition Street, MELBOURNE, VIC, 3000 169 105 Dohertys Road, LAVERTON NORTH, VIC, 3026 170 110 Hopkins Road, FULHAM, VIC, 3851 171 50 Flemington Road, PARKVILLE, VIC, 3052 172 494 Grieve Parade, ALTONA NORTH, VIC, 3025 173 44 Johns Way, RED CLIFFS, VIC, 3496 174 5 Lipton Drive, THOMASTOWN, VIC, 3074 175 55 Park Street, TATURA, VIC, 3616 176 66 Ham Street, KANGAROO FLAT, VIC, 3555 177 1741 Sydney Road, CAMPBELLFIELD, VIC, 3061 178 448 Epsom Road, FLEMINGTON, VIC, 3031 179 38 Dohertys Road, LAVERTON NORTH, VIC, 3026 180 118 Hammond Road, DANDENONG, VIC, 3175 181 299 McKoy Street, WODONGA, VIC, 3690 Authorised by the Chief Parliamentary Counsel 202 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Schedule 37—Scheduled activity premises Column 1 Column 2 Item Specified addresses 182 13 Reo Crescent, CAMPBELLFIELD, VIC, 3061 183 36–38 Charles Street, COBURG NORTH, VIC, 3058 184 22 Radford Road, RESERVOIR, VIC, 3073 185 160 Gordon Street, FOOTSCRAY, VIC, 3011 186 1239 Nepean Highway, CHELTENHAM, VIC, 3192 187 425 Burwood Highway, WANTIRNA SOUTH, VIC, 3152 188 54 Kelly Street, WODONGA, VIC, 3690 Part 2—Specified premises Column 1 Column 2 Item Specified premises 1 The premises at which a glass packaging plant is situated and that are bounded by Raleigh Street, Hudsons Road, Simcock Avenue, and Booker Street in Spotswood 2 The premises at which a char plant is situated on Porters Road in Morwell 3 The premises at which an asphalt plant is situated on Riding Boundary Road in Ravenhall 4 The Melbourne University Campus located on Grattan Street in Carlton and Parkville 5 The La Trobe University Campus located on Centreway in Bundoora 6 The premises at which a shipping container terminal is situated on Mackenzie Road in West Melbourne 7 The premises at which a sewage treatment plant is situated on Alan Bird Drive in Bangholme 8 The premises at which a sewage treatment plant is situated on East Road in Cocoroc 9 The premises at which a gold mine is situated on McCormicks Road in Fosterville Authorised by the Chief Parliamentary Counsel 203 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008

Schedule 37—Scheduled activity premises Column 1 Column 2 Item Specified premises 10 The premises at which a paper mill is situated on Traralgon West Road in Morwell 11 The Loy Yang Power Station located on Bartons Lane in Traralgon 12 The premises at which a gold mine is situated on Leviathan Road in Stawell 13 The premises located at the southwest corner of Henderson and Bosse Roads in Tongala 14 The premises located at the end of Janette Street in Traralgon 15 The premises at which a mineral sands mine is situated on Elliotts Road in Kanagulk ═══════════════ Authorised by the Chief Parliamentary Counsel 204 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Endnotes Endnotes 1 General information See www.legislation.vic.gov.au for Victorian Bills, Acts and current authorised versions of legislation and up-to-date legislative information. The Victorian Energy Efficiency Target Regulations 2008, S.R. No. 158/2008 were made on 11 December 2008 by the Governor in Council under section 75 of the Victorian Energy Efficiency Target Act 2007, No. 70/2007 and came into operation on 1 January 2009: regulation 3. The Victorian Energy Efficiency Target Regulations 2008 will sunset 10 years after the day of making on 11 December 2018 (see section 5 of the Subordinate Legislation Act 1994). INTERPRETATION OF LEGISLATION ACT 1984 (ILA) Style changes Section 54A of the ILA authorises the making of the style changes set out in Schedule 1 to that Act. References to ILA s. 39B Sidenotes which cite ILA s. 39B refer to section 39B of the ILA which provides that where an undivided regulation, rule or clause of a Schedule is amended by the insertion of one or more subregulations, subrules or subclauses the original regulation, rule or clause becomes subregulation, subrule or subclause (1) and is amended by the insertion of the expression "(1)" at the beginning of the original regulation, rule or clause. Interpretation As from 1 January 2001, amendments to section 36 of the ILA have the following effects: • Headings All headings included in a Statutory Rule which is made on or after 1 January 2001 form part of that Statutory Rule. Any heading inserted in a Statutory Rule which was made before 1 January 2001, by a Statutory Rule made on or after 1 January 2001, forms part of that Statutory Rule. This includes headings to Parts, Divisions or Subdivisions in a Schedule; Orders; Parts into which an Order is divided; clauses; regulations; rules; items; tables; columns; examples; diagrams; notes or forms. See section 36(1A)(2A)(2B). Authorised by the Chief Parliamentary Counsel 205 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Endnotes • Examples, diagrams or notes All examples, diagrams or notes included in a Statutory Rule which is made on or after 1 January 2001 form part of that Statutory Rule. Any examples, diagrams or notes inserted in a Statutory Rule which was made before 1 January 2001, by a Statutory Rule made on or after 1 January 2001, form part of that Statutory Rule. See section 36(3A). • Punctuation All punctuation included in a Statutory Rule which is made on or after 1 January 2001 forms part of that Statutory Rule. Any punctuation inserted in a Statutory Rule which was made before 1 January 2001, by a Statutory Rule made on or after 1 January 2001, forms part of that Statutory Rule. See section 36(3B). • Provision numbers All provision numbers included in a Statutory Rule form part of that Statutory Rule, whether inserted in the Statutory Rule before, on or after 1 January 2001. Provision numbers include regulation numbers, rule numbers, subregulation numbers, subrule numbers, paragraphs and subparagraphs. See section 36(3C). • Location of "legislative items" A "legislative item" is a penalty, an example or a note. As from 13 October 2004, a legislative item relating to a provision of a Statutory Rule is taken to be at the foot of that provision even if it is preceded or followed by another legislative item that relates to that provision. For example, if a penalty at the foot of a provision is followed by a note, both of these legislative items will be regarded as being at the foot of that provision. See section 36B. • Other material Any explanatory memorandum, table of provisions, endnotes, index and other material printed after the Endnotes does not form part of a Statutory Rule. See section 36(3)(3D)(3E). Authorised by the Chief Parliamentary Counsel 206 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Endnotes 2 Table of Amendments This publication incorporates amendments made to the Victorian Energy Efficiency Target Regulations 2008 by statutory rules, subordinate instruments and Acts. ––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––– Victorian Energy Efficiency Target Amendment (Assignment of Right) Regulations 2010, S.R. No. 109/2010 Date of Making: 12.10.10 Date of Commencement: 14.10.10: reg. 3 Victorian Energy Efficiency Target Amendment Regulations 2010, S.R. No. 127/2010 Date of Making: 26.10.10 Date of Commencement: Regs 5, 6(1), 7–10, 12, 13 on 28.10.10: reg. 3(1); regs 6(2), 11 on 1.7.11: reg. 3(2) Victorian Energy Efficiency Target Amendment (Scheme Target) Regulations 2011, S.R. No. 31/2011 Date of Making: 24.5.11 Date of Commencement: Reg. 6 on 31.5.11: reg. 3(1); reg. 5 on 1.1.12: reg. 3(2) Victorian Energy Efficiency Target Amendment (Ductwork and Standby Power Controllers) Regulations 2011, S.R. No. 56/2011 Date of Making: 5.7.11 Date of Commencement: 5.7.11 Victorian Energy Efficiency Target Amendment (Prescribed Activities) Regulations 2011, S.R. No. 146/2011 Date of Making: 6.12.11 Date of Commencement: Regs 5, 6(1), 7–25 on 7.12.11: reg. 3(1); reg. 6(2) on 1.1.12: reg. 3(2) Victorian Energy Efficiency Target Amendment (Prescribed Activities) Regulations 2012, S.R. No. 6/2012 Date of Making: 14.2.12 Date of Commencement: 14.2.12 Victorian Energy Efficiency Target Amendment (In-Home Displays) Regulations 2012, S.R. No. 14/2012 Date of Making: 28.2.12 Date of Commencement: 1.3.12: reg. 3 Victorian Energy Efficiency Target Amendment (Further Prescribed Activities) Regulations 2012, S.R. No. 32/2012 Date of Making: 15.5.12 Date of Commencement: 17.5.12: reg. 3 Victorian Energy Efficiency Target Amendment (Scheme Acquisitions) Regulations 2012, S.R. No. 43/2012 Date of Making: 13.6.12 Date of Commencement: 1.7.12: reg. 3 Authorised by the Chief Parliamentary Counsel 207 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Endnotes Victorian Energy Efficiency Target Amendment (Prescribed Activities) Regulations 2013, S.R. No. 24/2013 (as amended by S.R. No. 96/2013) Date of Making: 26.2.13 Date of Commencement: Regs 5–9 on 1.3.13: reg. 3(1); regs 10–14 on 19.4.13: reg. 3(2); regs 15–20 on 1.7.14: reg. 3(3) Victorian Energy Efficiency Target Amendment (Relevant Entity and Other Matters) Regulations 2013, S.R. No. 96/2013 Date of Making: 9.7.13 Date of Commencement: 10.7.13: reg. 3 Victorian Energy Efficiency Target Amendment Regulations 2014, S.R. No. 74/2014 Date of Making: 24.6.14 Date of Commencement: 30.6.14: reg. 3 Victorian Energy Efficiency Target Amendment Regulations 2015, S.R. No. 167/2015 Date of Making: 22.12.15 Date of Commencement: Regs 5–16 on 1.1.16: reg. 3(1); reg. 17 on 1.2.16: reg. 3(2); reg. 18 on 1.3.16: reg. 3(3) Victorian Energy Efficiency Target Amendment (Ceiling Insulation and Incandescent Lighting) Regulations 2016, S.R. No. 16/2016 Date of Making: 22.3.16 Date of Commencement: 4.4.16: reg. 3 Victorian Energy Efficiency Target Amendment (High Efficiency Televisions) Regulations 2016, S.R. No. 147/2016 Date of Making: 13.12.16 Date of Commencement: 1.1.17: reg. 3 Victorian Energy Efficiency Target (Project-Based Activities) Regulations 2017, S.R. No. 46/2017 Date of Making: 14.6.17 Date of Commencement: Regs 20‒22 on 19.6.17: reg. 3 Victorian Energy Efficiency Target Amendment (Weather Sealing) Regulations 2017, S.R. No. 52/2017 Date of Making: 20.6.17 Date of Commencement: 1.7.17: reg. 3 Victorian Energy Efficiency Target Amendment (Scheme Acquisition and Creation of Certificates) Regulations 2017, S.R. No. 71/2017 Date of Making: 11.7.17 Date of Commencement: 1.8.17: reg. 3 ––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––– Authorised by the Chief Parliamentary Counsel 208 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Endnotes 3 Amendments Not in Operation There are no amendments which were Not in Operation at the date of this publication. Authorised by the Chief Parliamentary Counsel 209 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Endnotes 4 Explanatory details Table of Applied, Adopted or Incorporated Matter The following table of applied, adopted or incorporated matter was included in S.R. No. 158/2008 in accordance with the requirements of regulation 5 of the Subordinate Legislation Regulations 2004. Statutory Rule Title of applied, adopted or Matter in Provision incorporated document applied, adopted or incorporated document regulation 4 AS 4234—1994 The whole Solar water heaters— Domestic and heat pump— Calculation of energy consumption regulation 4 Building Code of Australia meaning of glazing as defined in Part 1.1 and as used in Part 2.6 regulation 6(k) AS 3999—1992 The whole Thermal insulation of dwellings—Bulk insulation— Installation requirements regulation 6(l) AS 3999—1992 The whole Thermal insulation of dwellings—Bulk insulation— Installation requirements regulation 6(o) Building Code of Australia Part 3.8.5 regulation 6(q) AS/NZS 6400:2005 The whole Water efficient products— Rating and labelling Authorised by the Chief Parliamentary Counsel 210 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Endnotes Statutory Rule Title of applied, adopted or Matter in Provision incorporated document applied, adopted or incorporated document Schedule 1 AS 4234—1994 The whole as Solar water heaters— modified by Domestic and heat pump— Schedule 1, Calculation of energy Part A consumption Schedule 1 AS 4552/AG 102—2000 The whole Gas Water Heaters Schedule 1 AS 4552—2005 The whole Gas fired water heaters for hot water supply and/or central heating

Schedule 1, Part A AS/NZS 2712:2007 The whole Solar and heat pump water heaters—Design and construction Schedule 2, Part A AS/NZS 2712:2007 The whole Solar and heat pump water heaters—Design and construction Schedule 2, Part A AS 4234—1994 The whole as Solar water heaters— modified by Domestic and heat pump— Schedule 2 Calculation of energy Part A consumption

Schedule 2, Part A Guidelines to calculate annual The whole solar energy savings for domestic solar water heaters produced by adding a Retrofit Kit (collectors and pump) to an existing tank, Version 5.1 October 2008, Sustainability Victoria Authorised by the Chief Parliamentary Counsel 211 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Endnotes Statutory Rule Title of applied, adopted or Matter in Provision incorporated document applied, adopted or incorporated document Schedule 3, Part A AS/NZS 2712:2007 The whole Solar and heat pump water heaters—Design and construction

Schedule 3 AS 4234—1994 The whole as Solar water heaters— modified by Domestic and heat pump— Schedule 3, Calculation of energy Part A consumption Schedule 4, Part A AS/NZS 2712:2007 The whole Solar and heat pump water heaters—Design and construction Schedule 4 AS 4234—1994 The whole as Solar water heaters— modified by Domestic and heat pump— Schedule 4, Calculation of energy Part A consumption

Schedule 4 Guidelines to calculate annual The whole solar energy savings for domestic solar water heaters produced by adding a solar preheater to an existing gas hot water system, Version 2.3 October 2008, Sustainability Victoria

Schedule 5 AS 4556—2000 The whole (AG 106—2000) Indirect gas- fired ducted air-heaters

Schedule 6 AS 4556—2000 The whole (AG 106—2000) Indirect gas- fired ducted air-heaters Authorised by the Chief Parliamentary Counsel 212 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Endnotes Statutory Rule Title of applied, adopted or Matter in Provision incorporated document applied, adopted or incorporated document Schedule 7 AS/NZS 3823.1.2:2001 The whole Performance of electrical appliances—Airconditioners and heat pumps—Test methods—Ducted airconditioners and air-to-air heat pumps—Testing and rating for performance Schedule 7, Part A AS/NZS 3823.2:2005 The whole Performance of electrical appliances—Airconditioners and heat pumps—Energy labelling and minimum energy performance standard (MEPS) requirements

Schedule 7, Part A AS/NZS 3823.3:2002 The whole Performance of electrical appliances—Airconditioners and heat pumps—Performance of electrical appliances— Airconditioners and heat pumps (MEPS) Schedule 8 AS/NZS 3823.1.2:2001 The whole Performance of electrical appliances—Airconditioners and heat pumps—Test methods—Ducted airconditioners and air-to-air heat pumps—Testing and rating for performance Schedule 8, Part A AS/NZS 3823.2:2005 The whole Performance of electrical appliances—Airconditioners and heat pumps—Energy labelling and minimum energy performance standard (MEPS) requirements Authorised by the Chief Parliamentary Counsel 213 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Endnotes Statutory Rule Title of applied, adopted or Matter in Provision incorporated document applied, adopted or incorporated document Schedule 8, Part A AS/NZS 3823.3:2002 The whole Performance of electrical appliances—Airconditioners and heat pumps—Performance of electrical appliances— Airconditioners and heat pumps (MEPS) Schedule 9 AS 4553—2000 The whole (AG 103—2000) Gas space heating appliances

Schedule 9 AS 4553—2008 The whole Gas space heating appliances Schedule 10, Part A AS/NZS 3823.2:2005 The whole Performance of electrical appliances—Airconditioners and heat pumps—Energy labelling and minimum energy performance standard (MEPS) requirements Schedule 10 AS/NZS 3823.1.1:1998 The whole Performance of electrical appliances—Airconditioners and heat pumps—Test methods—Ducted airconditioners and air-to-air heat pumps—Testing and rating for performance

Schedule 11 AS/NZS 4859.1:2002 The whole Materials for the thermal insulation of buildings— General criteria and technical provisions Authorised by the Chief Parliamentary Counsel 214 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Endnotes Statutory Rule Title of applied, adopted or Matter in Provision incorporated document applied, adopted or incorporated document

Schedule 12 AS/NZS 4859.1:2002 The whole Materials for the thermal insulation of buildings— General criteria and technical provisions Schedule 13 AS 2047—1999 The whole Windows in buildings— Selection and installation

Schedule 13 AS 1288—2006 The whole Glass in buildings—Selection and installation Schedule 18 AS/NZS 4474.1:1997 The whole Performance of household electrical appliances— Refrigerating appliances— Energy consumption and performance Schedule 18 AS/NZS 4474.1:2007 The whole Performance of household electrical appliances— Refrigerating appliances— Energy consumption and performance

Schedule 18 AS/NZS 4474.2:2001 The whole Performance of household electrical appliances— Refrigerating appliances— Energy labelling and minimum energy standard requirements —— Authorised by the Chief Parliamentary Counsel 215 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Endnotes Table of Applied, Adopted or Incorporated Matter The following table of applied, adopted or incorporated matter was included in S.R. No. 127/2010 in accordance with the requirements of regulation 5 of the Subordinate Legislation Regulations 2004. In this table, Principal Regulations means the Victorian Energy Efficiency Target Regulations 2008. Statutory Rule Title of applied, adopted or Matter in Provision incorporated document applied, adopted or incorporated document Regulation 13 AS 4556–2000 The whole which inserts new (AG 106–2000) Indirect

Schedule 20 in the gas-fired ducted air heaters Principal Regulations published by The Australian Gas Association in August 2000 and reprinted August 2002 incorporating Amendments Nos 1 and 2. Regulation 13 AS/NZS 4847.1:2010 The whole which inserts new Selfballasted lamps for general

Schedule 21 in the lighting services—Part 1: Principal Regulations Test Methods— Energy performance 2nd Edition published by Standards Australia/Standards New Zealand on 21 May 2010. AS/NZS 4847.2:2010 The whole Self ballasted lamps for general lighting services— Part 2: Minimum Energy Performance Standards (MEPS) requirements 2nd Edition published by Standards Australia/Standards New Zealand on 21 May 2010. Authorised by the Chief Parliamentary Counsel 216 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Endnotes Statutory Rule Title of applied, adopted or Matter in Provision incorporated document applied, adopted or incorporated document IEC/TR 61341 Method of The whole measurement of centre beam intensity and beam angle(s) of reflector lamps Edition 2.0 2010-02. Published by the International Electrotechnical Commission on 18 February 2010. Regulation 13 AS/NZS 4474.1:1997 The whole which inserts new Performance of household

Schedule 22 in the electrical appliances— Principal Regulations Refrigerating appliances— Part 1: Energy consumption and performance published by Standards Australia/Standards New Zealand on 5 May 1997 and reissued December 2004 incorporating Amendments Nos 1, 2 and 3. AS/NZS 4474.1:2007 The whole Performance of household electrical appliances— Refrigerating appliances— Part 1: Energy consumption and performance 2nd Edition published by Standards Australia/Standards New Zealand on 15 August 2007 and reissued October 2008 incorporating amendment No. 1. Authorised by the Chief Parliamentary Counsel 217 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Endnotes Statutory Rule Title of applied, adopted or Matter in Provision incorporated document applied, adopted or incorporated document AS/NZS 4474.2:2009 The whole Performance of household electrical appliances— Refrigerating appliances Part 2: Energy labelling and minimum energy performance standard requirements 4th Edition published by Standards Australia/Standards New Zealand on 8 April 2009. Regulation 13 AS 2913–2000 The whole which inserts new Evaporative airconditioning

Schedule 23 in the equipment 2nd Edition Principal Regulations published by Standards Australia on 19 July 2000. Regulation 13 AS/NZS 62087.2.2:2010 The whole which inserts new Power consumption of audio,

Schedule 24 in the video and related equipment— Principal Regulations Part 2.2: Minimum energy performance standards (MEPS) and energy rating label requirements for television sets 2nd Edition published by Standards Australia/Standards New Zealand on 22 February 2010. Authorised by the Chief Parliamentary Counsel 218 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Endnotes Statutory Rule Title of applied, adopted or Matter in Provision incorporated document applied, adopted or incorporated document Regulation 13 AS/NZS 2442.1:1996 The whole which inserts new Performance of household

Schedule 25 in the electrical appliances—Rotary Principal Regulations clothes dryers—Part 1: Energy consumption and performance published by Standards Australia/Standards New Zealand on 5 March 1996 and reissued September 2006 incorporating Amendments Nos 1, 2, 3 and 4. AS/NZS 2442.2:2000 The whole Performance of household electrical appliances—Rotary clothes dryers—Part 2: Energy labelling requirements published by Standards Australia/Standards New Zealand on 31 March 2000 and reissued incorporating Amendment Nos 1 and 2 in April 2007. AS 4554–2005 The whole Gas laundry dryers published by Standards Australia on 19 December 2005. Authorised by the Chief Parliamentary Counsel 219 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Endnotes Statutory Rule Title of applied, adopted or Matter in Provision incorporated document applied, adopted or incorporated document Regulation 13 Voluntary Energy Rating The whole which inserts new Labelling Program for

Schedule 26 in Swimming Pool Pump-units: the Principal Rules for Participation, April Regulations 2010, published by the Equipment Energy Efficiency (E3) Committee. AS 5102.1–2009 The whole Performance of household electrical appliances— Swimming pool pump-units— Part 1: Energy consumption and performance published by Standards Australia on 21 December 2009. AS 5102.2–2009 The whole Performance of household electrical appliances— Swimming pool pump-units— Part 2: Energy labelling and minimum energy performance standard requirements published by Standards Australia on 21 December 2009. —— Authorised by the Chief Parliamentary Counsel 220 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Endnotes Table of Applied, Adopted or Incorporated Matter The following table of applied, adopted or incorporated matter was included in S.R. No. 56/2011 in accordance with the requirements of regulation 5 of the Subordinate Legislation Regulations 2004. In this table, Principal Regulations means the Victorian Energy Efficiency Target Regulations 2008. Statutory rule Title of applied, adopted or Matter in provision incorporated document applied, adopted or incorporated document Regulation 7 Australian Standard The whole which inserts new "Ductwork for air-handling

Schedule 28 in the systems in buildings" Principal Regulations AS 4254–2002 published by Standards Australia on 5 April 2002 and reissued incorporating Amendment Nos 1 and 2 in October 2004. Australian/New Zealand The whole Standard "Materials for the thermal insulation of buildings–Part 1: General criteria and technical provisions" AS/NZS 4859.1:2002 published by Standards Australia/Standards New Zealand on 15 October 2002 and reissued incorporating Amendment No. 1 in December 2006. Building Code of Australia Table 3.12.5.2 —— Authorised by the Chief Parliamentary Counsel 221 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Endnotes Table of Applied, Adopted or Incorporated Matter The following table of applied, adopted or incorporated matter was included in S.R. No. 146/2011 in accordance with the requirements of regulation 5 of the Subordinate Legislation Regulations 2004. Statutory Rule Title of applied, adopted or Matter in Provision incorporated document applied, adopted or incorporated document Regulation 8 which Australian/New Zealand The whole inserts new regulation Standard 6400:2005 6AA(g) into the Water efficient products - Principal Regulations Rating and labelling Regulation 18 which Australian Standard 4556— The whole amends Schedule 5 of 2011 the Principal Indirect gas-fired ducted air Regulations heaters —— Authorised by the Chief Parliamentary Counsel 222 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Endnotes Table of Applied, Adopted or Incorporated Matter The following table of applied, adopted or incorporated matter was included in S.R. No. 6/2012 in accordance with the requirements of regulation 5 of the Subordinate Legislation Regulations 2004. Statutory rule Title of applied, adopted or Matter in provision incorporated document applied, adopted or incorporated document Regulation 5 which AS 3999:1992 The whole substitutes new Thermal insulation of regulation 6(1)(k) dwellings—Bulk insulation— and (2)(a) into the Installation requirements Principal Regulations published by Standards Australia on 16 April 1992. Regulation 5 which AS/NZS 6400:2005 The whole substitutes new Water efficient products— regulation 6(1)(n) Rating and labelling published into the Principal by Standards Regulations Australia/Standards New Zealand on 1 June 2005 and reissued December 2006 incorporating Amendments Nos 1, 2 and 3. Regulation 5 which The 2008 edition of the Part 3.8.5 substitutes new Building Code of Australia regulation 6(2)(b) comprising— into the Principal (a) Volume One of the Regulations Australian Building Codes Board Series including any variations or additions in the Appendix Victoria set out in the Appendices to that Volume; and (b) Volume Two of the Australian Building Codes Board Series including any Victorian additions set out in Appendix A of that Volume. —— Authorised by the Chief Parliamentary Counsel 223 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Endnotes Table of Applied, Adopted or Incorporated Matter The following table of applied, adopted or incorporated matter was included in S.R. No. 14/2012 in accordance with the requirements of regulation 5 of the Subordinate Legislation Regulations 2004. Statutory rule Title of applied, adopted or Matter in provision incorporated document applied, adopted or incorporated document Regulation 5 which Minimum Functionality The whole inserts new definition Specification (Victoria) of AMI metering Release 1.1, published by the installation into the Department of Primary Principal Regulations Industries in September 2008 Regulation 7 ZigBee Smart Energy Profile The whole which inserts new Specification published by the Schedule 30 into the ZigBee Standards Organisation Principal Regulations on 1 December 2008 Regulation 7 ZigBee Smart Energy Profile The whole which inserts new Specification version 1.1

Schedule 30 into the published by the ZigBee Principal Regulations Standards Organisation on 23 March 2011 —— Authorised by the Chief Parliamentary Counsel 224 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Endnotes Table of Applied, Adopted or Incorporated Matter The following table of applied, adopted or incorporated matter was included in S.R. No. 32/2012 in accordance with the requirements of regulation 5 of the Subordinate Legislation Regulations 2004. Statutory rule Title of applied, adopted or Matter in provision incorporated document applied, adopted or incorporated document Regulation 5 which IEC 60034-2-1 Rotating The whole amends regulation 4 electrical machines - Part 2.1: of the Principal Standard method for Regulations determining losses and efficiency from tests (excluding machines for traction vehicles) published by the International Electrotechnical Commission on 10 September 2007. Regulation 5 which IEC/TS 60034-31 Rotating The whole amends regulation 4 electrical machines - Part 31: of the Principal Selection of energy-efficient Regulations motors including variable speed applications - Application guide published by the International Electrotechnical Commission on 26 April 2010. Regulation 6(1) Amendment No. 1 to The whole and (2) which inserts AS 3999—1992 Thermal new regulation insulation of dwellings— 6(1)(k) and (2)(a) Bulk insulation—Installation into the Principal requirements published by Regulations Standards Australia on 9 March 2012. Authorised by the Chief Parliamentary Counsel 225 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Endnotes Statutory rule Title of applied, adopted or Matter in provision incorporated document applied, adopted or incorporated document Regulation 6(4) The 2008 edition of the Part A3 and (5) which inserts Building Code of Australia new regulation comprising— 6(2)(d) and (3)(d) (a) Volume One of the into the Principal Australian Building Codes Regulations Board Series including any variations or additions in the Appendix Victoria set out in the Appendices to that Volume; and (b) Volume Two of the Australian Building Codes Board Series including any Victorian additions set out in Appendix A of that Volume. Regulation 38 Australian Standard 1731.14- The whole which inserts new 2003

Schedule 32 into the Refrigerated display cabinets - Principal Regulations Part 14: Minimum energy performance standard (MEPS) requirements published by Standards Australia on 1 October 2003 and reissued December 2005 incorporating Amendment No. 1. Regulation 38 Australian Standard 1731.9- The whole which inserts 2003 new Schedule 32 Refrigerated display cabinets - into the Principal Part 9: Electrical energy Regulations consumption test published by Standards Australia on 1 October 2003 and reissued December 2005 incorporating Amendment No. 1. Authorised by the Chief Parliamentary Counsel 226 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Endnotes Statutory rule Title of applied, adopted or Matter in provision incorporated document applied, adopted or incorporated document Regulation 38 Australian Standard 1731.12- The whole which inserts 2003 new Schedule 32 Refrigerated display cabinets - into the Principal Part 12: Measurement of the Regulations heat extraction rate of the cabinets when the condensing unit is remote from the cabinet published by Standards Australia on 1 October 2003 and reissued December 2005 incorporating Amendment No. 1. Regulation 10 Australian/ New Zealand The whole which inserts new Standard 1680.0:2009 regulation 10(2), Interior lighting - Part 0: Safe and regulation 38 movement published by which inserts new Standards Australia/Standards Schedule 34 into the New Zealand on 15 December Principal Regulations 2009. Regulation 10 Australian/ New Zealand Table 3.1 which inserts new Standard 1680.1:2006 regulation 10(2), Interior and workplace and regulation 38 lighting - Part 1: General which inserts new principles and Schedule 34 into the recommendations published Principal Regulations by Standards Australia/ Standards New Zealand on 21 February 2006. Authorised by the Chief Parliamentary Counsel 227 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Endnotes Statutory rule Title of applied, adopted or Matter in provision incorporated document applied, adopted or incorporated document Regulation 38 Australian/New Zealand The whole which inserts new Standard 4783.2:2002 Schedule 34 into the Performance of electrical Principal Regulations lighting equipment - Ballasts for fluorescent lamps - Part 2: Energy labelling and minimum energy performance standards requirements published by Standards Australia/Standards New Zealand on 23 December 2002. Regulation 38 The 2011 edition of the Part J6 which inserts new Building Code of Australia Schedule 34 into the comprising— Principal Regulations (a) Volume One of the Australian Building Codes Board Series including any variations or additions in the Appendix Victoria set out in the Appendices to that Volume; and (b) Volume Two of the Australian Building Codes Board Series including any Victorian additions set out in Appendix A of that Volume. Regulation 38 The 2012 edition of the Part J6 which inserts new Building Code of Australia

Schedule 34 into the comprising— Principal Regulations (a) Volume One of the Australian Building Codes Board Series including any variations or additions in the Appendix Victoria set out in the Appendices to that Volume; and Authorised by the Chief Parliamentary Counsel 228 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Endnotes Statutory rule Title of applied, adopted or Matter in provision incorporated document applied, adopted or incorporated document (b) Volume Two of the Australian Building Codes Board Series including any Victorian additions set out in Appendix A of that Volume. —— Table of Applied, Adopted or Incorporated Matter The following table of applied, adopted or incorporated matter was included in S.R. No. 24/2013 in accordance with the requirements of regulation 5 of the Subordinate Legislation Regulations 2004. Statutory rule Title of applied, adopted or Matter in provision incorporated document applied, adopted or incorporated document Regulation 6(6) Australian/New Zealand The whole which inserts Standard 6400:2005 Water regulation 6(3)(g) efficient products - Rating and into the Principal labelling. Published by Regulations, and Standards Australia/Standards regulation 9 which New Zealand on 1 June 2005 inserts Schedule 36 and reissued June 2011 into the Principal incorporating Amendments Regulations Nos 1, 2, 3, 4 and 5 Regulation 5 which ASTM F2324-03(2009) The whole amends regulation 4 Standard Test Method for of the Principal Prerinse Spray Valves. Regulations and Published by ASTM regulation 9 which International in 2009 inserts Schedule 36 into the Principal Regulations Authorised by the Chief Parliamentary Counsel 229 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Endnotes Statutory rule Title of applied, adopted or Matter in provision incorporated document applied, adopted or incorporated document Regulation 10 which Australian Standard 4234— The whole amends regulation 4 1994 Solar Water Heaters - of the Principal Domestic and heat pump - Regulations Calculation of energy consumption. Published by Standards Australia on 22 August 1994 Regulations 10 Australian/New Zealand The whole and 15 which amend Standard 4234:2008 Heated regulation 4 of the water systems—Calculation of Principal Regulations energy consumption. and regulations 11 Published by Standards to 14 which amend Australia/Standards New Schedules 1 to 4 of Zealand on 21 August 2008 the Principal and reissued November 2011 Regulations incorporating Amendments Nos 1 and 2 Regulations 11 to 14 Australian/New Zealand The whole which amend Standard 2712:2007 Solar and Schedules 1 to 4 of heat pump water heaters— the Principal Design and construction. Regulations Published by Standards Australia/Standards New Zealand on 12 September 2007 and reissued November 2011 incorporating Amendments Nos 1 and 2 Regulation 12 which Sustainability Victoria The whole amends Schedule 2 to Guidelines to calculate annual the Principal solar energy savings for Regulations domestic solar water heaters produced by adding a Retrofit Kit (collectors and pump) to an existing tank (version 6.0 updated June 2011). Published by Sustainability Victoria in June 2011 Authorised by the Chief Parliamentary Counsel 230 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Endnotes Statutory rule Title of applied, adopted or Matter in provision incorporated document applied, adopted or incorporated document Regulation 14 which Sustainability Victoria The whole amends Schedule 4 to Guidelines to calculate annual the Principal solar energy savings for Regulations domestic solar water heaters produced by adding a solar preheater to an existing gas hot water system, Version 3.0 June 2011. Published by Sustainability Victoria in June 2011 —— Table of Applied, Adopted or Incorporated Matter The following table of applied, adopted or incorporated matter was included in S.R. No. 167/2015 in accordance with the requirements of regulation 5 of the Subordinate Legislation Regulations 2014. In this table, Principal Regulations means the Victorian Energy Efficiency Target Regulations 2008. Statutory rule Title of applied, adopted or Matter in provision incorporated document applied, adopted or incorporated document Regulation 5 which Australian/New Zealand The whole inserts a definition of Standard 1359.5:2004 three-phase cage Rotating electrical machines— induction motor in General requirements regulation 4 of the Part 5: Three-phase cage Principal Regulations induction motors—High efficiency and minimum energy performance standards requirements, 2nd edition, published by Standards Australia and Standards New Zealand on 6 September 2004. Authorised by the Chief Parliamentary Counsel 231 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Endnotes Statutory rule Title of applied, adopted or Matter in provision incorporated document applied, adopted or incorporated document Regulation 9 which Australian/New Zealand The whole amends Schedule 7 to Standard 3823.2:2013 the Principal Performance of electrical Regulations, regulation appliances—Air conditioners 10 which amends and heat pumps Schedule 8 to the Part 2: Energy labelling and Principal Regulations, minimum energy performance and regulation 12 standards (MEPS) which amends requirements, 8th edition, Schedule 10 to the published by Standards Principal Regulations Australia and Standards New Zealand on 23 May 2013 Regulation 9 which Australian/New Zealand The whole amends Schedule 7 to Standard 3823.1.2:2012 the Principal Performance of electrical Regulations, regulation appliances—Airconditioners 10 which amends and heat pumps

Schedule 8 to the Part 1.2: Ducted Principal Regulations, airconditioners and air-to-air and regulation 12 heat pumps—Testing and which amends rating for performance

Schedule 10 to the (ISO 13253:2011, MOD), Principal Regulations 2nd edition, published by Standards Australia and Standards New Zealand on 11 May 2012 Authorised by the Chief Parliamentary Counsel 232 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Endnotes Statutory rule Title of applied, adopted or Matter in provision incorporated document applied, adopted or incorporated document Regulation 12 which Australian/New Zealand The whole amends Schedule 10 to Standard 3823.1.1:2012 the Principal Performance of electrical Regulations appliances—Airconditioners and heat pumps Part 1.1: Non-ducted airconditioners and heat pumps—Testing and rating for performance (ISO 5151:2010, MOD), 2nd edition, published by Standards Australia and Standards New Zealand on 11 May 2012 Regulation 13 which Australian Standard The whole amends Schedule 31 to 60034.1—2009 the Principal Rotating electrical machines Regulations Part 1: Rating and performance (IEC 60034-1, Ed. 11(2004) MOD), published by Standards Australia on 15 July 2009 Regulation 13 which International Electrotechnical The whole amends Schedule 31 to Commission Technical the Principal Specification 60034-31 Regulations Rotating electrical machines - Part 31: Selection of energy- efficient motors including variable speed applications - Application guide, published by the International Electrotechnical Commission on 26 April 2010 Authorised by the Chief Parliamentary Counsel 233 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Endnotes Statutory rule Title of applied, adopted or Matter in provision incorporated document applied, adopted or incorporated document Regulation 13 which International Electrotechnical The whole amends Schedule 31 to Commission International the Principal Standard 60034-2-1 Regulations Rotating electrical machines - Part 2-1: Standard methods for determining losses and efficiency from tests (excluding machines for traction vehicles), published by the International Electrotechnical Commission on 10 September 2007 Regulation 14 which Australian Standard The whole amends Schedule 32 to 1731.14—2003 the Principal Refrigerated display cabinets Regulations Part 14: Minimum energy performance standard (MEPS) requirements, published by Standards Australia on 1 October 2003 and reissued December 2005 incorporating Amendment No. 1 and July 2012 incorporating Amendment No. 2 Regulation 14 which Australian Standard The whole amends Schedule 32 to 1731.9—2003 the Principal Refrigerated display cabinets Regulations Part 9: Electrical energy consumption test, 2nd edition, published by Standards Australia on 1 October 2003 and reissued December 2005 incorporating Amendment No. 1 Authorised by the Chief Parliamentary Counsel 234 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Endnotes Statutory rule Title of applied, adopted or Matter in provision incorporated document applied, adopted or incorporated document Regulation 14 which Australian Standard The whole amends Schedule 32 to 1731.12—2003 the Principal Refrigerated display cabinets Regulations Part 12: Measurement of the heat extraction rate of the cabinets when the condensing unit is remote from the cabinet, 2nd edition, published by Standards Australia on 1 October 2003 and reissued December 2005 incorporating Amendment No. 1 Regulation 16 which The Building Code of Part A3 and amends Schedule 34 to Australia comprising— Part J6 the Principal (a) Volume One of the Regulations Australian Building Codes Board Series including any variations or additions in the Appendix Victoria set out in the Appendices to that Volume; and (b) Volume Two of the Australian Building Codes Board Series including any Victorian additions set out in Appendix A of that Volume Authorised by the Chief Parliamentary Counsel 235 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Endnotes Statutory rule Title of applied, adopted or Matter in provision incorporated document applied, adopted or incorporated document Regulation 17 which Australian//New Zealand The whole amends Schedule 21 to Standard 4847.2:2010 the Principal Self ballasted lamps for Regulations general lighting services Part 2: Minimum Energy Performance Standards (MEPS) requirements, 2nd Edition published by Standards Australia and Standards New Zealand on 21 May 2010 and reissued December 2011 incorporating Amendment No. 1 Regulation 17 which International Electrotechnical The whole amends Schedule 21 to Commission Technical Report the Principal 61341 Regulations Method of measurement of centre beam intensity and beam angle(s) of reflector lamps, Edition 2.0, published by the International Electrotechnical Commission on 18 February 2010 Regulation 18 which Australian/New Zealand The whole amends Schedule 21 to Standard 4847.2:2010 the Principal Self ballasted lamps for Regulations general lighting services Part 2: Minimum Energy Performance Standards (MEPS) requirements, 2nd Edition published by Standards Australia and Standards New Zealand on 21 May 2010 and reissued December 2011 incorporating Amendment No. 1 Authorised by the Chief Parliamentary Counsel 236 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Endnotes Statutory rule Title of applied, adopted or Matter in provision incorporated document applied, adopted or incorporated document Regulation 18 which International Electrotechnical The whole amends Schedule 21 to Commission Technical the Principal Report 61341 Regulations Method of measurement of centre beam intensity and beam angle(s) of reflector lamps, Edition 2.0, published by the International Electrotechnical Commission on 18 February 2010 —— Table of Applied, Adopted or Incorporated Matter The following table of applied, adopted or incorporated matter was included in S.R. No. 16/2016 accordance with the requirements of regulation 5 of the Subordinate Legislation Regulations 2014. In this table, Principal Regulations means the Victorian Energy Efficiency Target Regulations 2008. Statutory rule Title of applied, adopted or Matter in provision incorporated document applied, adopted or incorporated document Regulation 5, AS 3999:2015 The whole which amends Bulk thermal insulation— regulation 6(2)(a) Installation, published by of the Principal Standards Australia on 23 July Regulations, and 2015 regulation 6 which amends Schedule 11 to the Principal Regulations. Authorised by the Chief Parliamentary Counsel 237 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Endnotes Statutory rule Title of applied, adopted or Matter in provision incorporated document applied, adopted or incorporated document Regulation 6, which AS/NZS 4859.1:2002 The whole amends Schedule 11 Materials for the thermal to the Principal insulation of buildings— Regulations. Part 1: General criteria and technical provisions, published by Standards Australia/Standards New Zealand on 15 October 2002 and reissued in December 2006 incorporating Amendment No. 1 Regulation 7, which AS/NZS 4847.2:2010 The whole amends Schedule 21 Self ballasted lamps for to the Principal general lighting services— Regulations. Part 2: Minimum Energy Performance Standards (MEPS) requirements, 2nd Edition, published by Standards Australia/Standards New Zealand on 21 May 2010 and reissued December 2011 incorporating Amendment No. 1 Regulation 7, which International Electrotechnical The whole amends Schedule 21 Commission Technical to the Principal Report 61341 Regulations. Method of measurement of centre beam intensity and beam angle(s) of reflector lamps, Edition 2.0, published by the International Electrotechnical Commission on 18 February 2010 Authorised by the Chief Parliamentary Counsel 238 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Endnotes Table of Applied, Adopted or Incorporated Matter The following table of applied, adopted or incorporated matter was included in S.R. No. 147/2016 in accordance with the requirements of regulation 5 of the Subordinate Legislation Regulations 2014. Statutory rule Title of applied, adopted or Matter in provision incorporated document applied, adopted or incorporated document Regulation 4 which AS/NZS 62087.2.2:2011 The whole amends Schedule 24 Power consumption of to the Victorian audio, video and related Energy Efficiency equipment—Part 2.2: Target Regulations Minimum energy 2008 performance standards (MEPS) and energy rating label requirements for television sets, 3rd Edition published by Standards Australia/Standards New Zealand on 26 October 2011 and reissued June 2012 incorporating Amendment No. 1 and December 2012 incorporating Amendment No. 2 —— Table of Applied, Adopted or Incorporated Matter The following table of applied, adopted or incorporated matter was included in S.R. No. 52/2017 in accordance with the requirements of regulation 5 of the Subordinate Legislation Regulations 2014. In this table, Principal Regulations means the Victorian Energy Efficiency Target Regulations 2008. Authorised by the Chief Parliamentary Counsel 239 Victorian Energy Efficiency Target Regulations 2008 S.R. No. 158/2008 Endnotes Statutory rule Title of applied, adopted or Matter in provision incorporated document applied, adopted or incorporated document Regulation 6 The Building Code of Part 3.8.5 which substitutes Australia comprising— regulation 6(2)(b) (a) Volume One of the of the Principal Australian Building Codes Regulations Board Series including any variations or additions in the Appendix Victoria set out in the Appendices to that Volume; and (b) Volume Two of the Australian Building Codes Board Series including any Victorian additions set out in Appendix A of that Volume Regulation 9 The Building Code of Part 3.8.5 which substitutes Australia comprising—

Schedule 15 to (a) Volume One of the the Principal Australian Building Codes Regulations Board Series including any variations or additions in the Appendix Victoria set out in the Appendices to that Volume; and (b) Volume Two of the Australian Building Codes Board Series including any Victorian additions set out in Appendix A of that Volume Authorised by the Chief Parliamentary Counsel 240